User manual US ROBOTICS USR5450 QUICK START

[. . . ] 802. 11g Wireless Turbo Multi-function Access Point Quick Installation Guide Package Contents: - 802. 11g Wireless Turbo Multi-function Access Point - Installation CD-ROM - Two (2) detachable antennas - 5VDC power supply - Quick Installation Guide Note: Be sure to find out what letter your CD-ROM drive uses before you begin installing your new product. You will need to know this to properly install your software. Verify detection of the 54 Mbps Wireless Access Point After the Wireless Access Point is installed, double-click the icon for the Configuration Utility on your desktop. If the 802. 11g Wireless Turbo Multi-function Access Point is located, the configuration information will be displayed. Note: It is recommended that the 802. 11g Wireless Turbo Multi-function Access Point is always configured via an Ethernet connection. [. . . ] This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy. If this equipment is not installed and used in accordance with the manufacturer's instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The use of shielded cables for connection of the monitor to the graphics card is required to assure compliance with FCC regulations. Modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Detachable Antenna Information FCC Part 15, Subpart C, Section 15. 203 Antenna requirement USR 5450 users: An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section. The manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. Try moving closer to the 802. 11g Wireless Turbo Multi-function Access Point and repeating the scan procedure. Check any physical connections between the 802. 11g Wireless Turbo Multi-function Access Point and your modem, router, hub, LAN, or switch. My computer is not acknowledging my 802. 11g Wireless Turbo Multi-function Access Point. Possible Solution: Be certain that the 802. 11g Wireless Turbo Multi-function Access Point is plugged into a power source and is properly installed. Make sure the Ethernet cable is securely connected to the Ethernet port on the 802. 11g Wireless Turbo Multi-function Access Point and to the Ethernet port on your cable or DSL modem, router, hub, or switch. U. S. Robotics Corporation Two (2) Year Limited Warranty 1. 0 1. 1 1. 2 1. 3 1. 4 1. 5 GENERAL TERMS: This Limited Warranty is extended only to the original end-user purchaser (CUSTOMER) and is not transferable. No agent, reseller, or business partner of U. S. ROBOTICS) is authorised to modify the terms of this Limited Warranty on behalf of U. S. This Limited Warranty expressly excludes any product that has not been purchased as new from U. S. This Limited Warranty is only applicable in the country or territory where the product is intended for use (As indicated by the Product Model Number and any local telecommunication approval stickers affixed to the product). [. . . ] ROBOTICS will make reasonable effort to ship repaired or replaced product or part to CUSTOMER, at U. S. ROBOTICS expense, not later than TWENTY ONE (21) DAYS after U. S. ROBOTICS receives the authorized CUSTOMER return at an authorised U. S. ROBOTICS shall not be liable for any damages caused by delay in delivering or furnishing repaired or replaced product or part. [. . . ]