User manual US ROBOTICS USR5470 INSTALLATION GUIDE

[. . . ] Wireless Starter Kit 802. 11g 54Mbps Router 802. 11g 54Mbps USB Adapter Installation Guide Guide d'installation Installationsanleitung Guida all'installazione rapida Guía breve de instalación Beknopte installatiegids R24. 0496. 00 English 802. 11g 54Mbps Router Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 802. 11g 54Mbps USB Adapter Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Troubleshooting and Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 USR5470 Package Contents USR5462 802. 11g 54Mbps Router 19VAC Power Supply Installation Guide One (1) Ethernet cable USR5422 54Mbps USB Adapter Installation CD-ROM 802. 11g 54Mbps Router Installation Prepare for Installation Note: It is important that you have your serial number written down before you install the 802. 11g 54Mbps Router. [. . . ] If you cannot connect to the Internet or to the correct Wireless Router, verify your configuration settings and then refer to the Troubleshooting section in this Guide or in the User Guide on the Installation CD-ROM. You have finished installing the 802. 11g 54Mbps USB Adapter and the 802. 11g 54Mbps Router. You should now have shared Internet access through the 802. 11g 54Mbps Router. For troubleshooting and technical support information, refer to the Troubleshooting section in this Guide or to the User Guide on the U. S. Robotics Installation CD-ROM. Register your products · At the Installation CD-ROM interface, click the Support link. Click Product Registration and then click http://www. usr. com/productreg You can also launch a Web browser and type in http://www. usr. com/productreg · 8 Troubleshooting and Support If you have any difficulties connecting to the 802. 11g 54Mbps Router, check the following top three issues and see if they apply to your situation. · If you are attempting to create a wireless connection but cannot connect to the 802. 11g 54Mbps Router, make sure each wireless card is set to Infrastructure mode. If the wireless cards are set to 802. 11g Ad hoc mode, you will not be able to connect to the 802. 11g 54Mbps Router. When each wireless card is set to Infrastructure mode, it should automatically connect to the Access Point of the 802. 11g 54Mbps Router. If the wireless cards do not automatically connect, rescan until they detect the 802. 11g 54Mbps Router and connect. · If you create a wireless connection to the 802. 11g 54Mbps Router but are experiencing poor link quality, check the positioning of the 802. 11g 54Mbps Router. Long distances, multiple floors, or steel or concrete walls can diminish the link quality. If possible, reposition the 802. 11g 54Mbps Router to reduce the effect of any of these obstacles. Make sure the address of the subnet mask is 255. 255. 255. 0. The Default Gateway should be the IP address of the 802. 11g 54Mbps Router, which is 192. 168. 2. 1. To verify all of these settings, perform the following steps: Windows 95, 98, or Me Users: Click Windows Start and then Run. Check the IP Address, Subnet Mask, Default Gateway, and DNS server data to make sure they are correct. If the information is not correct, click Release All and then click Renew All. Windows NT, 2000, or XP Users: Click Windows Start and then Run. Check the IP Address, Subnet Mask, Default Gateway, and DNS server data to make sure they are correct. If the information is not correct, type ipconfig /release and press ENTER. Then, type ipconfig /renew and press ENTER. My Web User Interface for the 802. 11g 54Mbps Router is not responding, but I can still access the Internet. Possible Solution: If your Web User Interface stops responding, unplug and then plug back in the power supply of the 802. 11g 54Mbps Router. This will reboot the 802. 11g 54Mbps Router. [. . . ] Robotics Installation CD-ROM did not automatically launch when I inserted the Installation CD-ROM. Possible Solution: Some programs may keep the autolaunch feature of the Installation CD-ROM from beginning. Close any open applications and reinsert the Installation CD-ROM. If your CD-ROM still does not automatically launch, click Windows Start, Run, and type D:\setup (if your CD-ROM drive uses a 12 different letter, type that letter in place of "D") and click OK. I accidentally clicked Cancel during the installation procedure. Possible Solution: Remove and reinsert the U. S. Robotics Installation CD-ROM into your CD-ROM drive. [. . . ]