User manual VAISALA DMP248

[. . . ] DMP248 Dewpoint Transmitter OPERATING MANUAL M210492EN-A JULY 2003 PUBLISHED BY Vaisala Oyj P. O. Box 26 FIN-00421 Helsinki Finland Phone (int. ): Fax: (+358 9) 894 91 (+358 9) 8949 2227 Visit our Internet pages at http://www. vaisala. com/ © Vaisala 2003 No part of this manual may be reproduced in any form or by any means, electronic or mechanical (including photocopying), nor may its contents be communicated to a third party without prior written permission of the copyright holder. The contents are subject to change without prior notice. _________________________________________________________________________CONTENTS Table of contents CHAPTER 1 GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 SAFETY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 0. 0 <cr> Press any key when ready. . . · · · T Change the temperature and again check the transmitter against the reference. Check that the reading corresponds with the reading of the reference instrument. Press any key, enter the second point value and press <cr>. : xx. x Ref2 ?yy. y <cr> VAISALA _________________________________________________________________________ 61 OPERATING MANUAL _______________________________________________________________ · The stabilization of the sensor can be monitored well by entering c <cr> instead of the reference value. Using display/keypad commands · Leave the reference instrument and the transmitter for at least 4 hours in the same space so that their temperatures have time to equalize. Remove the filter cap prior to calibration. Disconnect the security lock jumper before turning the transmitter on!· · Check the transmitter against the reference. Select Cali in the main menu and then T; select two-point calibration T 2 point cal. Change the first point reading with the arrow keys and press ENT. Change the temperature and again check the transmitter against the reference. Check that the reading corresponds with the reading of the reference instrument. If necessary, change the second point reading with the arrow keys and press ENT. · · · Using LED commands · Leave the reference instrument and the transmitter for at least 4 hours in the same space so that their temperatures have time to equalize. Remove the filter cap prior to calibration. Disconnect the security lock jumper before turning the transmitter on!· · Check the transmitter against the reference. Connect an ammeter/voltmeter to the analogue outputs (connector X2). At the first calibration point the LED on the left flashes; adjust the first point (offset) with the arrow switches to the same reading with the reference and press ENT switch. Change the temperature and again check the transmitter against the reference. · 62_____________________________________________________________________M210492EN-A CHAPTER 6 ______________________________________________ CALIBRATION AND ADJUSTMENT · · Check that the reading corresponds with the reading of the reference instrument. If necessary, adjust with the arrow switches to the correct value and press ENT. At the second calibration point the second LED from the left flashes. Calibration of the analogue outputs The analogue outputs have been calibrated at the factory and since they are very stable, calibration of the outputs should be performed only when there is reason to believe that their adjustments have changed. Using serial commands Disconnect the security lock jumper! ACAL <cr> The outputs on channels 1 and 2 are measured and the measured values (mA or V) entered as calibration coefficients. Example: both channels have 0. . . 10 V outputs (set with AMODE command); enter the voltages measured at the analogue outputs: >ACAL <cr> Ch1 U1 ( V Ch1 U2 ( V Ch2 U1 ( V Ch2 U2 ( V ) ) ) ) ?0. 123 <cr> 9. 98 <cr> 0. 120 <cr> 9. 98 <cr> Using display/keypad commands Disconnect the security lock jumper!· Connect an ammeter/voltmeter to the output of channel 1, select Cali in the main menu and Analog outputs in the Cali menu. The following is displayed (the quantity can be either mA or V): VAISALA _________________________________________________________________________ 63 OPERATING MANUAL _______________________________________________________________ · Enter the measured lower end current/voltage on channel 1. · Enter the measured upper end current/voltage on channel 1. · Connect the meter to the output of channel 2 and enter the measured lower end current/voltage on channel 2. · Enter the measured upper end current/voltage on channel 2. Using LED commands If both the analogue outputs and humidity/temperature channels are calibrated, the analogue outputs should be calibrated first. [. . . ] Attach the grounding wire with the screw and washer to the grounding terminal on the right-hand VAISALA ________________________________________________________________________ 131 APPENDIX 7_________________________________________________________________________ side of the module if the mains power is in use. Attach the ribbon cable from X3 of the alarm unit to the X16 on the main board of the transmitter. NOTE NO jumper in connector X4 during normal operation. When one alarm unit relay is on, the corresponding LED is lit. ribbon cable M3 screws (4 pcs) for mounting (prefix with fibre washers) X16 X3 M4 screw and washer for protective ground terminal +- ++- probe cable gland signal cable gland arrange signal cable wires so that they do not reach bare AC wires when the cover is closed replace the plastic plug with cable gland for ¢7. . . 12 mm cable cable: strip wires only 5 mm; use crimped terminal for ground wire if stranded wire is used Prefix the fastening screws with fiber washers for mounting the unit to the box. NOTE The alarm unit cannot be used with the power supply unit HMP230PW. WARNING Do not detach the alarm unit from the transmitter when the power is on. WARNING Do not connect the mains power to alarm unit without grounding the transmitter. 132____________________________________________________________________M210492EN-A APPENDIX 7 ________________________________________________________________________ Setting and activating the outputs with menu commands Disconnect the security lock jumper!· Select MORE in the main menu and then ALARM; the following is displayed: · If the settings need to be changed, press CL: - the quantity starts blinking; it can be changed with arrow switches, and acknowledged with ENT. [. . . ]