User manual VAISALA WHP25

[. . . ] 14 Figure 8 Wiring WAC151 with WHP25 Mains Power Supply and WA25 Wind Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Figure 9 Wiring WAT12 with WHP25 Mains Power Supply and WA25 Wind Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Figure 10 Location of the Fuses F1 and F2. . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Figure 11 WHP25 Main Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The WHP25 unit provides two power outputs, namely 24. 0 VDC (max 5. 2 A) and 38. 0 VAC (max 0. 9 A). The WHP25 unit has a waterproof housing made from cast aluminum. The mounting hardware is included in the delivery. It is mountable to a Ø 100 mm standard pole mast. VAISALA___________________________________________________________7 User's Guide ________________________________________________________ 0212-184 Figure 1 WHP25 Mains Power Supply The following numbers refer to Figure 1 above: 1 2 3 = Gland for AC (mains) input cable = Gland for optional power output cable = Gland for power output cable 8 ______________________________________________________ M210376en-A Chapter 3 __________________________________________________ Installation CHAPTER 3 INSTALLATION This chapter provides you with information that is intended to help you install WHP25 Mains Power Supply. Installation Procedure Before installation, route the input (AC) power cable near the mast, which WHP25 Mains Power Supply will be mounted to. Make sure you selected a pole mast with a diameter from 99 to 105 mm for installation with the standard mounting clamp. To install the WHP25 unit, follow the procedure below. Remove the four screws holding the cover of the WHP25 unit. Attach the unit to the mast at a suitable place with the provided accessories and the standard mounting clamp. Refer to Figure 2 on page 10. VAISALA___________________________________________________________9 User's Guide ________________________________________________________ 0212-185 Figure 2 Mounting WHP25 Mains Power Supply on a Pole Mast The following numbers refer to Figure 2 above. = Enclosure = Slot screw M6, washer A6, spring washer B6, and nut M6 = Mounting clamp = Pole mast, diameter from 99 to 105 mm = Cable gland = Cable If the local voltage level is other than 230 VAC, reselect the voltage with the X2 and X3 jumpers located inside the WHP25 unit. For the location of the jumpers, refer to Figure 3 on page 11. For instructions how to set the jumpers for different input voltages, refer to Figure 4 on page 11. WARNING Improper jumper setting damages WHP25 Mains Power Supply. CAUTION Observe the instructions and warnings in the instruction label inside the unit, refer to Figure 4 on page 11. 10 _____________________________________________________ M210376en-A Chapter 3 __________________________________________________ Installation 0212-186 Figure 3 Location of the WHP25 Jumpers The following numbers refer to Figure 3 above. 1 2 3 = Plastic shield above the jumpers = Caution label = Fixing screw for the plastic shield F1 X1 2AT Primary FUSES 8AT Secondary F2 X4 12345678 MAINS VOLTAGE (X2, X3) Factory setting 230V 245V 38VAC 0. 9A ACout (RG13H) 24VDC 5. 2A DCout (WA25) 100V X2 115V 200V 215V ELN X3 NOTE!Total wire resistance less than 0. 3 ohms recommended for WA25 systems. MAINS INPUT 1. 0 - 2. 0 A WARNING!Improper jumper setting may cause damage. Figure 4 4. 5. Instructions Label for the WHP25 Jumper Settings and Wiring Make sure the AC (mains) voltage is disconnected. Enter the AC (mains) cable through the leftmost cable gland and connect the input wiring to the X1 VAISALA__________________________________________________________11 User's Guide ________________________________________________________ connector. To ease the wire connection the connector has spring loaded terminals. Connect the ground wire to the crimp assembled under the screw. The wiring of the AC (mains) input to the X1 connector is instructed in Figure 4 on page 11. Refer to Figure 5 below for the location of the connectors and cable glands on the WHP25 unit. Tighten the input cable glands. 7. 0212-187 Figure 5 WHP25 Connectors and Glands The following numbers refer to Figure 5 above. [. . . ] Pack the faulty product using an ESD protection bag of good quality with proper cushioning material in a strong box of adequate size. Please include the Problem Report in the same box. Send the box to: Vaisala Oyj SSD Service Vanha Nurmijärventie 21 FIN-01670 Vantaa Finland 3. 6. 22 _____________________________________________________ M210376en-A Chapter 5 _______________________________________________Technical Data CHAPTER 5 TECHNICAL DATA This chapter provides the technical data for WHP25 Mains Power Supply. Specifications Table 3 WHP25 Mains Power Supply Specifications Description/Value 230 VAC ±10 %, 50/60 Hz, 1. 0 A max. 100/115/200/215/245 VAC (±10 %) 24. 0 ±2. 5 VDC, 5. 2 A (max. ) 38. 0 ±3. 0 VAC, 0. 9 A (max. ) Property Input operating power: Nominal Optional selections DC output (X4/4, 5 - 6, 7) AC output (X4/1 - 2) Fuses: Primary 24 V output 38 V output Cable glands (3) 2 AT replaceable fuse, 5 × 20 mm 8 AT replaceable fuse, 5 × 20 mm 1. 8 A solid state fuse One for input, two for outputs, cable 7 . . . [. . . ]