User manual VARIZOOM FLOWPOD

[. . . ] Tighten only enough to secure the handle. When using the supplied hex key to tighten or loosen the counter weights, grip firmly, insert the hex head thoroughly, and do not overtighten. To prevent damage, hold on to the camcorder while adjusting the mounting plate (X-Y plate) to ensure that it doesn't slide and fall. It may take a little while to learn how to use the FlowPod properly, so please read the instructions thoroughly before attempting to use it. As packed, the unit is configured for basic stabilizer mode, and you will have to complete a few steps before you will be ready to shoot. STABILIZER MODE Attachment and Balancing 1. [. . . ] Because of the variety of accessories and configurations available for DV cameras, it isn't possible to prescribe an exact weighting guide. See section 6 to determine how much counter-weight you need. 3 5. Adjust the X-Y assembly so that your camera's mass is centered. Loosen the brake (white nylon screw) and adjust the X-Y assembly front-to-back and left-to-right so that the camera becomes level. Once the camcorder is balanced, tighten the adjustment screws thoroughly. 6. Now you can check the vertical balance of the FlowPod to see if you need to add, remove, or adjust the position of the counter-weights. Use as few weights as possible, and start with the weights at the top of the shaft (see picture below, "T"). Continue reading: "The Drop Test" To test the vertical balance, hold the unlocked handle straight up and turn the FlowPod on its side to a horizontal position (A), then let it fall back to the vertical position (the "Drop Test"). It should fall gradually, taking 2-3 seconds to go from horizontal to vertical. Note that it will swing past the vertical position ­ you are only counting the time it takes to go 90 degrees (from horizontal to vertical). If it does not swing down, slide your weights down one at a time (B) and retry the Drop Test. If that doesn't help, add another weight and retest. If the FlowPod swings down too fast, you should remove weights or slide them upward, as necessary. NOTES: -With some very small cameras, you may need to add a weight above the gimbal to achieve a good balance. -With heavier cameras you may need more than 3 counter-weights, available direct from VariZoom. T B 90° A 7. After setting your counter-weight, you may want to fine-tune the X-Y adjustments. Once you have achieved a good balance, you are ready to begin practicing with the FlowPod. There are two important things to keep in mind at this point: (1) The FlowPod is designed to be operated with two hands and (2) it requires practice to master (but it only gets easier with time). You can adjust the drag on left-right movement by slightly tightening the brake just above the handle, or you can leave it completely loose and steer with your free hand. Keep the handle unlocked for operation, and we recommend using your free hand to steer and aid in stabilizing the unit. Using your thumb and forefinger, lightly grasp the `neck' of the black C-handle (right by the brake) to control the left-right movement. Practice walking with the unit and try to hold it close to your body. [. . . ] Special Note: If at some point you don't need the monopod feature and want to use the FlowPod as a standalone stabilizer, just unscrew the monopod section from the main unit (counter-clockwise from the bottom) and remove it. This may be especially useful if you are using a very small camera that does not need much counter-weight. Also Available: VZ-DV Sportster ­ Upgrade to a vest and spring-arm supported system by adding the DV Sportster to your FlowPod http://www. varizoom. com/flowcam/dvsportster. php The VZ-FP has a one-year factory warranty that covers defects in materials or workmanship. Please retain your sales receipt for warranty verification. If you have any problems or questions, please contact us on the web (www. varizoom. com) or toll-free 888-826-3399. 7 VZ-FPB Balancing/Docking Plate for the FlowPod The VZ-FPB consists of the mounting plate and a c-clamp Using the VZ-FPB is simple, but first you may have to adjust the foam grip on your FlowPod handle. [. . . ]