User manual VDO CYCLECOMPUTING C10WL

[. . . ] English Deutsch Français Italiano Español page Seite page 1-18 19-38 39-56 GB C10WL D C10WL F C10WL I C10WL E C10WL NL C10WL pagine 57-74 pagina 75-92 Nederlands pagina 93-110 ETRTO 47-305 47-406 34-540 47-507 23-571 40-559 44-559 47-559 50-559 54-559 57-559 37-590 20-571 16x1, 75 20x1, 75 24x1 3/8 24x1, 75 26x1 26x1, 5 26x1, 6 26x1, 75 26x1, 9 26x2, 00 26x2, 125 26x1 3/8 26x3/4 WS in mm KMH 1272 1590 1948 1907 1973 2026 2051 2070 2089 2114 2133 2105 1954 WS in inch MPH 50, 1 62, 6 76, 7 75, 1 77, 7 79, 8 80, 7 81, 5 82, 2 83, 2 84, 0 82, 9 76, 9 ETRTO 32-630 40-622 47-622 40-635 37-622 18-622 20-622 23-622 25-622 28-622 32-622 37-622 40-622 27x1 1/4 28x1, 5 28x1, 75 28x1 1/2 28x1 3/8 700x18C 700x20C 700x23C 700x25C 700x28C 700x32C 700x37C 700x40C WS in mm KMH 2199 2224 2268 2265 2205 2102 2114 2133 2146 2149 2174 2205 2224 WS in inch MPH 86, 6 87, 6 89, 3 89, 2 86, 8 82, 8 83, 2 84, 0 84, 5 84, 6 85, 6 86, 8 87, 6 INSTALLATION AND OPERATION MANUAL - VDO CYTEC C 10 WL GB Preface Thank you for buying a VDO CYTEC bicycle computer. The more familiar you get with this model, the more enjoyable your trips are going to be. Please read thoroughly all the information provided in this manual. You are getting important and useful hints for operation to make you fully benefit from all the technical features of your VDO CYTEC bicycle computer. [. . . ] Start Scroll Set-up mode for your second trip counter TCNT Step 1: Call TCNT information into display. Display shows "TCNT" and a flashing number. Step 3: By pressing MODE 2 key, the number can be changed. Step 4: By pressing MODE1 key you proceed to the next number, which you can change by pressing MODE 2 key. Step 5: Once you have entered the last number for your TCNT, exit set-up mode by pressing MODE 1 key for 3 sec. . Watch out: When you exit set-up without having completed entering your data, the computer may well work with faulty values leading to misinformation in your display. Press MODE 2 5sec. Reset Reset TCNT to zero The second trip counter TCNT is reset to zero by pressing MODE 2 key for 5 sec. Before resetting to zero, make sure that TCNT information is called into display. Watch out: Pressing the MODE 2 key for 5 sec. without TCNT data being displayed probably resets your TRP-RID-AVS-MAX data to zero. 8 10. Manual stop-watch STP Your VDO CYTEC C 10 WL features a manual stop-watch. With information STP being displayed, you may operate your stop-watch with the MODE 2 -button. GB C 10 WL Watch out: Pressing the MODE 2 button for 5 sec. without STP data being displayed resets your TRP-AVS-RID-MAX data to zero. MODE 2 START/STOP Press MODE 2 5sec. Reset MODE 2 MODE 2 MODE 2 press when STP is displayed = starting the stop-watch press again = interrupt the stop-watch press again = stop watch continues 9 11. Comparison of current and average speed GB Your VDO CYTEC C 10 WL compares your current speed with your average speed. The outcome of this comparison can C be seen in your display by the use of symbols. No matter which information is currently displayed, this data keeps you 10 updated on the relation of your current speed and your average speed. WL Your current speed is faster than your average speed. Accuracy +/- 1 KMH/MPH You are currently riding as fast as your average speed. Accuracy +/- 1 KMH/MPH Your current speed is slower than your average speed. Set-up mode Your VDO CYTEC C 10 WL features the following set-up procedures wheelsize 1 = WS1 wheelsize 2 = WS2 clock = CLK odometers = ODO Trip Counter=TCNT set-up starts out of TRP in display set-up starts out of TRP in display set-up starts out of CLK in display set-up starts out of ODO in display set-up starts out of TCNT in display No matter which set-up mode is used for your VDO CYTEC , the procedure is the same. You can start the set-up mode for a certain display by pressing the MODE 1 button for 5 sec. [. . . ] This information is singly reset to zero. Information must be reset to zero by pressing the MODE 2 button for 5 sec. Watch out: Take care that the exact information to be reset is on display. If either of the following information, TRP, RID, AVS or MAX are displayed and you want to reset to zero by pressing the MODE 2 button, be aware that the remaining three information are simultaneously zeroed. 18. Stand-by-mode Your computer VDO CYTEC C 10 WL features a stand-by-mode in order to save battery power. [. . . ]