User manual VDO DAYTON MI 2200

[. . . ] Osservare le norme del proprio paese che regolamentano la visione di video negli autoveicoli. Observera At se video under kørslen kan nedsætte din opmærksomhed betydeligt og aflede den fra trafikken. For ikke at udsætte passagerer og andre trafikanter for fare bør føreren ikke se video under kørslen. Overhold venligst de lokale forskrifter vedrørende brug af video i bilen. 3 GENERAL INFORMATION Notes on operating instructions The following reading aids are used to simplify these operating instructions: Requests you to perform an action. Provides additional information. Identifies a list. 6 Shows that the current topic is continued on the following page. [. . . ] Only install in vehicles with 12V on-board voltage and negative earth. Risk of malfunction, damage and vehicle fire if installed in unsuitable vehicles (e. Do not damage safety system wiring (airbag etc. ). (Lines are normally specially marked, for example by labels. ) Do not use test lamps to test the voltage, since excessively high currents can damage / destroy electronic components. Insulate all solder points with shrink hose or insulating tape. Fit toothed washers at earth connections to the vehicle body. If necessary, remove paint and dirt beforehand. Subsequently, protect bare metal against corrosion. In order to ensure perfect installation, use only the original components supplied. The use of non-authorised components may result in malfunction. Do not install the unit positions where it is exposed to high temperatures, dust, dirt or excessive vibration (e. g. due to direct sunlight or heating vents). Scope of delivery 1 1 4 1 1 MI 2200 Multi Media Interface Power cable Self-tapping screws 5 x 20 mm Installation and operating instructions Remote control RCM 5500 Taking safety precautions, Fig. 1 Before starting work, disconnect the earth cable from the negative terminal of the vehicle battery, in order to prevent short circuits. At the same time, follow the vehicle manufacturer's safety instructions (alarm system, airbag, immobiliser, radio coding etc. ). A 7 English INSTALLATION INSTRUCTIONS Electrical connections, Fig. For wiring details, refer to the connection diagram on the back cover page and to the following table. Instead, wind them together and secure to one side. They may be required for retrofitting additional functions. Power supply cable Wire colour Yellow Red Black Blue/white Blue/yellow Green Grey Connection + 12 V permanent positive (must be rated for at least 4 A. ) + 12 V ACC / ignition positive (without switch-off on starting engine) Battery negative (body) + 12 V remote input AV1 (activates the audio / video input 1) + 12 V remote input AV2 (activates the audio / video input 2) + 12 V reversing signal (reversing light positive), active at + 12 V (active high) + 12 V parking brake signal, active at earth potential (active low) A A Only connect electrical signals to suitable connecting points in the vehicle. For direct connection of permanent positive (yellow lead) to the battery, the fuse must be no further than 10 - 15 cm from the positive terminal of the battery. If it is necessary to extend the positive lead, an additional 10 A fuse must be provided close to the battery (max. Failure to do so may result in a wiring fire hazard. s 12 V permanent positive (yellow): Connect yellow wire to a suitable connector with 12 V permanent positive. A This connection should be rated for a current of at least 4 amps. s 12 V ignition / ACC / accessory contact (red): Connect red wire to a suitable 12 V circuit switched through the ACC ignition key contact. s Battery negative (black) Connect black wire to a suitable earthing point on the vehicle body. s 12 V remote inputs AV1 and AV2 In order to ensure full functionality of the MI 2200, the external video sources should be provided with a 12 V remote control output. a) Remote input AV1 (blue/white): Connect blue/white wire to 12 V remote control output of the video source to be connected to the AV1 input of the MI 2200. [. . . ] Adaptation du volume sonore des sources vidéo connectées. Possibilité de raccordement d'un terminal pour sièges arrière RST 5400 en option. Principe de fonctionnement L'interface multimédia MI 2200 permet de disposer d'un système multimédia avec un équipement minimum. Vous avez la possibilité de raccorder au MI 2200 les sources vidéo de votre choix (p. un lecteur DVD VDO Dayton DV 6100), une caméra de rétrovision VDO Dayton et un ordinateur de navigation. [. . . ]