User manual VDO CONTISYS OBD

[. . . ] ContiSys OBD Instruction Manual 08/2009 - EN(2. 0) 08/2009 - EN(2. 0) 2 Contents Introduction Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Display screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] This results in distance to the next service being displayed as zero and the Service Reset fails to be completed. To reset the Service Interval the following procedure must be performed: 1. Press the [MODE] button on the dashboard to enter the dashboard functions menu. Use the [+] and [-] buttons on the dashboard to navigate to the UNITS option and press [MODE] to select. Use the [MODE], [+] and [-] buttons to set the units to Kilometres. All other settings should be left unchanged. Use the [+] and [-] buttons on the dashboard to navigate to the END MENU option and press [MODE] to exit the functions menu. Plug the service tool into the Diagnostic Socket (using the 16-pin FAL LS CAN harness) and perform a Service Reset by selecting FastCheck Service, Alfa Romeo, Mannesman then Service Reset. Disconnect the service tool, leaving the ignition on. Press the [MODE] button on the dashboard to enter the dashboard functions menu. Use the [+] and [-] buttons on the dashboard to navigate to the UNITS option and press [MODE] to select. Use the [MODE], [+] and [-] buttons to set the units back to Miles. All other settings should be left unchanged. Use the [+] and [-] buttons on the dashboard to navigate to the SERVICE option and press [MODE] to select. 'Number of Miles to Service' should now read approximately 12500 miles. Use the [+] and [-] buttons on the dashboard to navigate to the END MENU option and press [MODE] to exit the functions menu. This procedure is necessary to ensure that the value read from the Odometer by the dashboard, when a Service Reset is performed by the service tool, is in Kilometres. The Dashboard can then calculate the 'Number of Miles to Service' correctly. On the European Continent this procedure is not necessary as all dashboards are in Kilometres. BMW vehicles Note: To switch the ignition ON for vehicles fitted with a start/stop button, insert the remote key-fob fully into the ignition slot then press the start/stop button once (without any foot pedals depressed). Manufacturer BMW Option 1 CBS Digital reset Option 2 Service options Oil reset Distance reset Time reset Oil Inspection service Analogue reset Use the and keys to select the required menu option and press the selection. To return to a previous menu, press the key. to confirm The screen will display the message "BMW Reset" to confirm the reset process was completed successfully. [. . . ] Volvo 240 (1990 - 1993) 30 9 3 40 20 20 10 6 km/h 0 005000 mph CON0039 1. Remove the plug from the face of the instrument panel between the clock and the speedometer. Insert a thin-bladed tool into the cavity and press the reset button. 111 Appendix D: Manual service reset Volvo 740 (1986 - 1988) 9 6 service 3 005000 0 km/h mph CON0037 Reach behind the instrument panel and push the button located to the left of the speedometer. Volvo 740 (1989 - 1992) 30 9 3 40 20 20 10 6 km/h 0 005000 mph CON0039 1. [. . . ]