User manual VELODYNE DEQ-8R DATASHEET

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual VELODYNE DEQ-8R. We hope that this VELODYNE DEQ-8R user guide will be useful to you.

Lastmanuals help download the user guide VELODYNE DEQ-8R.


Mode d'emploi VELODYNE DEQ-8R
Download

You may also download the following manuals related to this product:

   VELODYNE DEQ-8R REV B (838 ko)
   VELODYNE DEQ-8R REV C (579 ko)
   VELODYNE DEQ-8R DATASHEET 2 (458 ko)

Manual abstract: user guide VELODYNE DEQ-8RDATASHEET

Detailed instructions for use are in the User's Guide.

[. . . ] Note: Do not leave unit in direct sunlight or use in high humidity environments!!!To prevent fire or shock hazard, do not expose this product to rain or moisture. To avoid electrical shock, do not open the speaker enclosure or amp chassis cover. Please observe all warnings on the equipment itself. [. . . ] In this case, Velodyne assumes no liability for any and all injuries to any persons involved, or for any property damage, whether to the subwoofer or any other property involved or damaged as a result of this unauthorized mains voltage change. (2) SPEAKER LEVEL INPUT Terminals Connect these input terminals to the speaker output terminals of your amplifier or receiver. If you use this method of connection, when you go to the receiver speaker set up menu, make sure you select the large speaker option. SPEAKER LEVEL OUTPUT Terminals Sends a crossed-over speaker-level signal to the front speakers. See below for a more detailed explanation of this crossover. IR INPUT This is a connection to allow you to purchase a third-party infrared remote sensor on an extended cable for placement closer to your other remote controlled equipment. This keeps you from awkward control angles using the infrared remote control. LINE OUTPUT Connect these jacks to the LINE IN preamp input to use the DEQ-R's internal high pass crossover. The signal fed from these connectors is rolled off below 120 Hz. LINE INPUT/LFE Connect these jacks to the LINE OUT preamp output, LFE output, or subwoofer output jacks of your receiver/processor. If using the LFE output from your receiver or processor, plug the single cable into the "L" ­ LFE input or, for more signal, use a "Y" connector (not included) and feed the signal into both "R" and "L" inputs. power down) the unit, turn off the power switch on the back panel. · MUTE -- This button mutes the subwoofer's output. The LED on the sub will show 00 if the unit is muted. To unmute the subwoofer, press the MUTE button again and the original volume setting shows on the LED. Figure 2: DEQ-R Remote. · EQ -- This button automatically equalizes the subwoofer's output so that it sounds best for its position in the room. To use this feature, remove the grille and plug the supplied microphone into the Mic-In jack on the front baffle of the sub and place the mic in your preferred listening position. Then press EQ on the remote for about 2-3 seconds. The subwoofer emits 12 "sweep tones" that span the frequencies between 20 and 150 Hz. The LED displays "AU" during the Auto-EQ process. After the sweeps are complete, the unit saves its EQ settings and returns to normal operation. To prevent accidental invocation of the EQ feature, you must hold down the EQ button for 2-3 seconds before the EQ sweeps begin. If the mic is not plugged in, the subwoofer sweeps twice then reverts back to normal functioning without changing any EQ settings. [. . . ] Under more serious conditions, the unit may shut off completely. Normal operation should return upon cooling, but you may be required to turn the power off and then on again to reset the unit. The following conditions require service by a qualified technician: 1. The unit does not appear to operate normally or exhibits a marked change in performance 3. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE VELODYNE DEQ-8R

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual VELODYNE DEQ-8R will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag