User manual VELODYNE DLSR5000BK

[. . . ] CAUTION RI S K O F E L E CT R I C SH O C K DO NOT OPEN Caution To reduce the risk of electric shock, do not remove cover (or back). Refer servicing to qualified service personnel. DLS -R Series TM The lighting flash with arrowhead symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the subwoofer. Read Instructions -- All safety and operating instructions should be read before the subwoofer is operated. [. . . ] The subwoofer's response will begin rolling off above the frequency you set this control to. You should set the crossover frequency to obtain a smooth and seamless transition from the subwoofer to the main speakers in your system. If your main speakers are smaller units with limited low frequency output, you may wish to choose a higher frequency (such as 100-120 Hz) than you would with larger speakers which have greater low frequency output. With larger speakers, you might start with this control set lower, such as 80 Hz. Subwoofer Direct Subwoofer Direct is a setting on the low-pass crossover knob and will allow frequencies up to 200 Hz into the subwoofer. See below for a more detailed explanation of this feature. Speaker Level Output/Line Level Output Rear Panel Connections ­ Detailed Explanation Your new subwoofer is equipped with both speaker-level and line-level inputs. Use the RCA/Phono type "INPUT" jacks when connecting your subwoofer to a pre-amp, signal processor, or line-level crossover. The "SPEAKER LEVEL INPUT" jacks connect directly to the speaker outputs of an integrated amplifier or receiver. Your amplifier section will notice no additional loading effects when you use these inputs because of their high impedance. Note: Do not use both the RCA/Phono "INPUT" connections and "SPEAKER LEVEL INPUT" connections simultaneously. When connected in this fashion, your satellite speakers will be crossed over at 80 Hz. This removes the lower bass from your satellites, enabling them to do a better job reproducing high frequencies and giving your receiver's amp more headroom (up to 50% more power). You may also connect your satellites directly to your receiver or amplifier along with the subwoofer if you wish to bypass this crossover. Caution!!! To avoid damage to your main amplifier, be sure to maintain correct polarity when making all connections. Red (positive) to red, and black (negative) to black. Be sure that all connections are tight, and that there are no loose strands or frayed wires. Power Switch The master power switch is located on the lower right half of the unit. This rocker style switch is the main on/off for the unit. This switch should be set to position 1 for on (up), 0 for off (down). 6 7 A Word About Your Receiver's Crossover and the DLS-R Crossover Placement True subwoofers operate at extremely low frequencies, which are primarily omni-directional. While it is recommended that the subwoofers be placed on the same plane as the satellite speakers, room and system conditions often dictate otherwise. Keep in mind that frequency response and output level can be drastically influenced by placement, depending on the acoustic properties of your listening room. Typically, the optimum location for a subwoofer is in a front corner of your listening room. This location will usually offer the greatest output levels and optimum low frequency extension. The worst location for a subwoofer is typically far away from any walls, close to the center of your room and near an opening or door way. When using a pair of Velodyne subwoofers in stereo, it is preferable to place each subwoofer near the satellite of the same channel. Typically, a minimum distance of 1 to 2 feet from your TV to the subwoofer will be adequate to avoid any magnetic interference. Your Velodyne DLS-R subwoofer is designed to operate using the full range audio signal for input when using the built-in crossover (controlled by the dial on the back panel). [. . . ] Normal operation will return upon cooling, but you may be required to turn the power off and then on again to reset the unit. The following conditions require service by a qualified technician: 1. The unit does not appear to operate normally or exhibits a marked change in performance. Some part of the cabinet or circuitry is physically damaged. 375 watts Dynamic/ 16" x 15" x 17. 75" 40 x 37. 5 x 44 2" four-layer copper 10" forward firing DLS-3750R Two years (parts and labor) Warranty 55 oz. Before seeking service for your subwoofer, please re-check all systems. [. . . ]