User manual VESTAX GE-62A

[. . . ] This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to. 10. Power sources-This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. [. . . ] If the product dose not operate normally by following the operating instructions. Adjust only those controls that are coverd by the operating instructions as an improper adjustment of other, controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. If the product has been dropped or cabinet has been damaged. When the product exhibits a distinct change in perfromance-this indicates need for service. 16. Replacement Parts-When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characterristics as the original parts. Unauthorized substitutions may result in fire, electric shock or other hazards. Safety Check-Upon completion of any service or repairs to product, ask the service technician to perfrom sefety checks to determine that the product is in proper operating condition. Carts and Stands-The appliance should be used only with a cart stand that is recommended by manufacturer. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn. SPECIFICATION FEATURES FUNCTIONS PROGRAM INPUT SECTION NOTE oPGM TRIM Adjusts the input level of each PGM channels. For acoustic clarity, set the INPUT FADER and MASRER FADER to a position of 7-8. *Replace this fader with a Vestax CF-PCV replacement inputfader. @0 C. F. CURVE SELECT SWITCH Adjusts the crossfader curve. A clockwise rotation gives a gentle crossfade, good for long running mixes, whereas a counter clockwise rotation gives a sleep crossfade which is good for scratching and cutting. MONITOR SECTION @3 MONITOR MODE SELECT SWITCH When this switch is set to "SPLIT", the master signal is always heard through the right ear-cup with the "monitor" PGM being heard in the left ear-cup. The monitor PGM sent the headphone is controlled through the MONITOR MODE SELECT SWITCH. When set to "STEREO" no master output is heard in the headphones, and only the signal selected by MONITOR SELECT SWITCH will be heard in both ear-cups. @4 MONITOR MODE LED This LED will be illuminated when the MONITOR MODE SELECT SWITCH@3 is on. @5 PHONES JACK Use this jack to connect headphones. Headphones with an impedance of 8ohm to 600ohm can be used on this unit. *For best sound quality Vestax recommends using Headphones with 150ohm impedance. @1 MONITOR EQ (HI/LOW) Adjusts the HI and LOW frequencies for Headphone monitoring. @2 MONITOR LEVEL Adjusts the headphone monitor level. MASTER SECTION #1 METER ASSIGN SWITCH Use this switch to select either MASTER OUT 1 or 2 to be shown in the MASTER LEVEL METER #0. #2 POWER LED This LED will be illuminated when the POWER SWITCH %4 is on. #3 AUX SEND LEVEL Adjusts the output level sent to an external effects unit connected to the AUX SEND JACK $9 on the rear panel. When the crossfader is used, this signal is taken after the crossfader but before the master fader. This makes a variety of techniques possible, such as the application of echo to a cut out in which the crossfader would be used. #4 AUX RCV LEVEL Adjusts the input level from an external effect unit connected to the AUX RCV JACK %0 on the rear panel. #5 AUX CUE ON/OFF SWITCH Sends the signal of external effects unit connected to the AUX SEND JACK to the MONITOR section for headphone monitoring. #6 AUX CUE LED This LED will be illuminated when the AUX CUE SWITCH#5 is on. #7 AUX RCV LEVEL METER This LED bar level meter indicates the level of the AUX RCV JACK signal. @6 MASTER BALANCE 1&2 #8 BOOTH OUT EQ (HI/LOW) @7 MASTER LEVEL 1&2 Adjusts the HI and LOW frequencies for the Adjusts the signal balance of the L to R side of the BOOTH OUT. outputs from MASTER OUT 1&2 JACKS %2 on the #9 BOOTH OUT LEVEL rear panel. Adjusts the signal level outputs from MASTER OUT 1&2 JACKS on the rear panel. $0 MUTE SWITCH This switch mutes the signal being sent to BOOTH OUT. @8 MASTER 1&2 CUE SWITCH Used to send the signal from the MASTER OUT 1&2 to the monitor section for headphone monitoring. $1 MUTE LED This LED will be illuminated when the MUTE SWITCH $0 is on. @9 MASTER 1&2 CUE LED This LED is illuminated when the MASTER 1&2 CUE SWITCH @8 is on. $2MASTER 1&2 & BOOTH OUTPUT LEVEL SELECTOR (ATTENUATION). Located under the top panel, this switch adjusts the output level for Master 1&2 in addition to the Booth out put level. [. . . ] %4 POWER SWITCH $9 AUX SEND JACK Power on/off. Connects to the input of external effects devices. %5POWER JACK (Delay, Reverb, etc) Connect the Vestax AC-20 , AC adaptor. %0 AUX RCV JACK Connects to the output of external effects devices. %4 FIRE EVACUATION CONTROL (JACK) This feature has been added in order to ensure that venues using the GE-62A are in compliance with modern fire safety standards. If a Fire Alarm is correctly connected to the GE-62A and is triggered in an evacuation emergency, the GE-62A will react to such a signal (alarm) by swiftly canceling the output of all but the MIC signal(s). [. . . ]