User manual VESTAX PCV-180

[. . . ] is left unattended and unused for long periods of time, unplug it from the wall 6. Attachments-Do not use attachments not outlet. This will prevent damage to the recommended by the product manufacturer product due to lightning and power-line as they may cause hazards. Water and Moisture-Do not use this product 12. [. . . ] Object and Liquid Entry-Never push objects of any kind into this product through 8. Accessories-Do not place this product on an openings as they may touch dangerous unstable cart, stand, tripod, or table. The voltage points or short-out parts that could product may fall, causing serious injury to a result in a fire or electric shock. Never spill child or adult, and serious damage to the liquid of any kind on the product. stand, tripod, bracket, or table recommended by 14. Servicing-Do not attempt to service product the manufacturer, or sold with product. Any yourself as opening or removing covers mounting of the appliance should follow the may expose you to dangerous voltage or manufacturer's instructions, and should use other hazards. Refer all servicing to a mounting accessory recommended by the qualified personnel. Damage Requiring Service-Unplug this 16. Replacement Parts-When replacement product from the wall outlet and refer parts are required, be sure the service servicing to qualified service personnel technician has used replacement parts under the following conditions: specified by the manufacturer or have the same characteristics as the original parts. When the power-supply cord or plug is Unauthorized substitutions may result in damaged. When the cross fader is set in the center, both programs will be heard. This is a detachable fader for the ease of replacement with "CF-RUS" "CF-R" or "CF-PCV" when it is worn out. i PHONES JACK Use this jack to connect the head phones. Head phones from 8 ohm to 600 ohm can be used. o MASTER LEVEL Adjusts the signal level output from the LINE OUT jack on the rear panel. !0 MASTER BALANCE Adjusts the signal balance of the left and right side of the outputs from the LINE OUT jack on the rear panel. !1 MONITOR LEVEL Adjusts the head phone output level. !2 MONITOR SELECT FADER When the monitor levels of PGM1 and PGM2 are properly set, PGM1 will be monitored in the headphone with the fader set to the left side and PGM2 will be monitored in the head phone with the fader set to the rigth side. When the fader is set in the center, both programs will be monitored in the head phone. !3 MIC LEVEL Adjusts the input level from all microphone inputs. 5 How to change the fader unit. HOW TO REMOVE THE TOP PANEL 1 Remove all fader knobs and the 4screws which driver fix the top panel. (see fig. A) 2 Remove the top panel. HOW TO CHANGE THE FADER UNIT 1 Remove the screws on the fader panel. (see fig. B) 2 Remove the fader unit from position in mixer. 3 Carefully remove the multi-cable connector from fader unit. (see fig. C) 4 Attach multi-cable connector to new fader unit. 5 Position the fader unit carefully and secure with screws. Remove the multi-cable connector from fader unit. fig. A driver Remove four scews. 4 fig. C You can replace the CF unit with "CF-RUS", "CF-R" or "CF-PCV". HOW TO REPLACE THE CF UNIT WITH "CF-PCV" When the fader unit is replaced, please see fig. C. [. . . ] Place the fader unit in the proper position and fix it with two screws. (fig. D- b ) CAUTION There is a swith for "CF-PCV" unit. When "CFPCV" unit is installed, set the switch to "PCV" mode. fig. B CAUTION When the fader unit is replaced, do not loosen the screws with marking. fig. D CF-RUS or CF-R CF-PCV 6 REAR PANEL 19 18 17 RISK OF ELECTRIC SHOCK. DO NOT OPEN WARNING;SHOCK HAZARD-DO NOT OPEN. AVIS;RISQUE DE CHOC ELELCTRIQUE -NE PAS OUVRIR. MADE IN CHINA UNDER LICENCE OF VESTAX TOKYO, JAPAN OUTPUT REC LINE 2 PGM 2 PGM 1 LINE 1 MIC SERIAL NO. DC IN LINE PHONO 2 PHONO 1 POWER DC15V R L R L R GND L 14 15 16 20 !4 POWER SWITCH !8 INPUT JACK 2 The POWER LED that is located on the top Used for PGM2 input. [. . . ]