User manual VESTAX PMC-270A

[. . . ] Objects have fallen, or liquid has been spilled into the and headphone or speakers, may be capable of producing product ; or sound levels that could cause permanent hearing loss. The product has been exposed to rain ; or operate for a long period of time at a high volume level or at a D. The product does not appear to operate normally or level that is uncomfortable. exhibits a marked change in perfromance ; or 5. [. . . ] This allows DJs to use hand carried DAT or MD player mixing with installed equipment. TOP PANEL PROGRAM INPUT SECTION PRO FESSIONAL MIXING CONTROLLER PMC-270A MASTER +8 +8 +5 +3 +1 0 -1 -3 -5 -7 -10 -15 POWER LINE 4 IN INPUT L R PHONO 1 PGM 1 INPUT LINE 2 PHONO 2 SUB INPUT LINE 4 PHONO 3 PGM 2 LINE 6 CUE +5 +3 MIC TRIM LINE 1 LINE 3 LINE 5 +1 0 MASTER SECTION TRIM TRIM -1 -3 MIC-1 MIC-1 MIC-2 MIN MAX MIN MAX MIN MAX -5 -7 -10 -15 POWER MICROPHONE AND SUB INPUT SECTION BAL BAL BAL MIN MAX L R L R L R MIC-2 EQ HI EQ HI EQ HI L R EFFECT SEND MIN MAX -16dB +16dB -16dB +16dB -16dB +16dB EQ HI MID MID MID MIN MAX RETURN -16dB +16dB -12dB +12dB -12dB +12dB -12dB +12dB LOW LOW LOW LOW MIN MAX CUE -16dB +16dB -16dB +16dB -16dB +16dB -16dB +16dB EFFECT OFF POST EFFECT PRE OFF POST EFFECT PRE OFF POST EFFECT PRE OFF POST OFF ON MASTER BAL CUE OFF ON CUE OFF SIGNAL ON CUE OFF SIGNAL ON CUE OFF SIGNAL ON L R LEVEL 10 9 8 7 6 5 4 3 2 1 0 10 9 8 7 6 5 4 3 2 1 0 10 9 8 7 6 5 4 3 2 1 0 MIN MAX MONITOR SPLIT CUE ON OFF PHONES LEVEL MIN MAX PHONES IN PGM1 ISOLATOR PGM2 ISOLATOR LOW MID HI 1 2 LOW MID HI ISOLATOR SECTION PHONES IN PROGRAM INPUT SECTION PGM 1 INPUT PHONO 1 LINE 2 PROGRAM INPUT SECTION 1. INPUT SELECTOR Used to select input (2 line or 1 phono) to be sent to each PGM channel. TRIM CONTROL Adjusts the Input level of each channel. adjust TRIM so that the INPUT LEVEL METER shows about 0dB. BALANCE CONTROL Adjusts the stereo balance for each PGM channel. Can be used for adjusting the unbalanced stereo image caused by a strong anti-skating setting. Clockwise rotation from center position increases the volume of R over L channel. A counter clockwise rotation increases the volume of L channel over R. EQUALIZER(HI, MID, LOW) Adjusts the HI, MID, LOW frequencies for each PGM channel. HI 8kHz 12dB Shelving type MID 500Hz 16dB Peaking type LOW 80Hz 12dB Shelving type 5. EFFECT SWITCH This switch enables the signal from each programs to be sent to AUX send jack. Different signal routes can be selected this switch to different positions. P R E : The signal before the input fader ( after the EQ ) will be sent to AUX output. POST : The signal after the input and cross fader will be sent to AUX output. O F F : No signal will be sent to AUX output. CUE SWITCH Used to send the signal from each program to monitor section for headphone monitoring. INPUT FADER Used to adjust the Input level of each program. This is a detachable fader for Remove four screws. Replace with the IF-27 when it is worn out. Remove the multiHOW TO REPLACE THE INPUT FADER cable connector from Remove four screws which hold the fader unit. Take the unit out with the panel Carefully remove the multi-cable connector from the fader unit. Insert the connector to the new fader unit. [. . . ] When the switch is put back, the output volume returns to normal. Can be useful for cutting off the sound of the cymbals or high hats for example. 26, MID SWITCH Allows cutting off the sound of the middle range. Sound volume will be cut when the switch is set downward position. [. . . ]