User manual VESTAX PMC-CX

[. . . ] When the product exhibits a distinct change in perfromance-this indicates need for service. Replacement Parts-When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characterristics as the original parts. Unauthorized substitutions may result in fire, electric shock or other hazards. Safety Check-Upon completion of any service or repairs to product, ask the service technician to perfrom sefety checks to determine that the product is in proper operating condition. [. . . ] Can be used !4 INPUT LEVEL VOLUME for adjusting the unbalanced stereo image. Clockwise rotation Adjusts the Input level of each program. Typically this from center position increases the volume of R over L channel. This fader is user A counter clockwise rotation increases the volume of L replaceable and may be changed easily by following this channel over R. users guide's instructions carefully. See "HOW TO t PGM ISOLATOR HI CHANGE THE FADER UNIT". Adjusts the HI frequency level of each PGM. *Replace this fader with a Vestax IF-500 replacement inputfader. y PGM ISOLATOR MID Adjusts the MID frequency level of each PGM. u PGM ISOLATOR LOW Adjusts the LOW frequency level of each PGM. HOW TO CHANGE THE FADER UNIT MIC / LINE SECTION @9 SUB MIC LEVEL VOLUME Adjusts the input level of the SUB MIC input. REAR PANEL #0 MAIN MIC / SUB LINE SELECTOR Selects between MAIN MIC and SUB LINE input. #1 MIC / LINE EQ VOLUME Adjusts the HI and LOW frequencies for the signal chosen by MAIN MIC / SUB LINE SELECTOR. #2 MIC / LINE LEVEL VOLUME Adjusts the input level of the MAIN MIC or SUB LINE input. #3 MIC / LINE CUE SWITCH Sends the signal from the MIC or LINE channel to the monitor section for headphone monitoring. When switch is on, an indicator lights up. #8 MAIN/SUB MIC JACK [MAIN MIC: XLR JACK (BALANCED), SUB MIC: PHONE JACK (UNBALANCED)] Input jack for MIC. $7 MASTER OUT 1/2 JACK [1/4' PHONE JACK (UNBALANCED), XLR JACK (BALANCED] Connect to the input on a power amplifier. These jacks are Phone type for consumer applications. This mixer has two sets of MASTER OUT jacks so that the each output level can be set separately. Therefore, the MASTER OUT can be used for main output or sub output IE. One for the main area and the other for entrance. #9 LINE INPUT JACK MONITOR SECTION #4 SPLIT / STEREO SELECTOR When this switch is set to "SPLIT", the master signal is always heard through the right ear-cup of the headphone. The signal selected by each CUE SWITCH will be heard in the left ear-cup. This enables both programs to be monitored simultaneously, thus assisting in beat mixing. When this switch is set to "STEREO" no master output is heard in the headphones, and only the signal selected by each CUE SWITCH will be heard in both ear-cups. [LINE: RCA PIN JACK, SUB LINE: 1/4' PHONE JACK (UNBALANCED)] Input connectors for line level equipment such as CD players, CD-R/RW players, MD players, tape decks, DVD players, DAT and VTR etc. $8 MASTER OUT LEVEL SELECT SWITCH [-10/0dB] Select the attenuation level for the BOOTH OUT. $0 PHONO INPUT JACK $9 MASTER LOOP SEND JACK Input jacks for turntables. Connect turntables equipped with MM (pick up) cartridge. Connects the input terminal of an external effector. (Delay, Reverb, etc. ) $1 GND TERMINAL #5 HEADPHONE EQ VOLUME Adjusts the HI and LOW frequencies for Headphone monitoring. #6 HEADPHONE LEVEL VOLUME Adjusts the headphone monitor level. Connect this terminal to the ground lead of the turntable. [. . . ] Power sources-This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. Lightning-For added protection for this product during lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage to the product due to lightning and power-line surges. [. . . ]