User manual VIETA HAM50

[. . . ] Control Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 The unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Do not place the remote control on a wet object. Do not place the remote control under the direct sunlight or near sources of excessive heat. Do not use caustic cleaners (porcelain, stainless steel, toilet, or oven cleaner etc. ) on the remote, as it may suffer damage. 6 5 Turning the Power On and Off Insert the AC/DC adapter's DC plug into the unit, then insert one side of AC power cord into a wall outlet, and your unit is at your command!* This unit has a built-in Recharge Li-lon battery, you can also insert the AC/DC adapter's DC plug into the unit for charging, the indicator will light up. The indicator will turn off when the built-in Recharge Li-lon battery is full power . Turning the Unit On Press the button for 2 seconds or more to turn the unit on from standby mode. Caution: When turning the unit on, the unit will continue in the mode it was in when it was turned off last time. Turning the Unit Off Press the button for 2 seconds or more to turn the unit off and go to standby mode. Caution: Be sure to unplug the power cord from the outlet when the unit is not in use for an extended period of time. Note: For saving power, If you don't use any function of the unit for about 30 seconds in playing mode, the LED will turn drak. And if you don't use any function of the unit for about 1 minute in playing mode when using the built-in Recharge Li-lon battery, the LED will turn off. Press any one button to returns to the original display. 7 6 Using the Unit Listening to music from an i-Pod (i-Pod player is not supplied): 1. Place the appropriate corresponding universal i-Pod adaptor, included with i-Pod, into this unit i-Pod docking location, then connect your i-Pod. A LED will indicate that the unit is on. Press the button again or +/- buttons on the remote or rotate the volume control knob on the front of unit to resume sound. Listening to Radio Broadcasts: This unit has built-in FM antenna. If reception is poor, please connect the supplied FM antenna to the FM antenna socket on the rear of the unit, then adjust the position of the FM antenna for the best reception. Caution: Disconnect the audio cable when using the FM antenna. Tuning in a Station 1. A LED will indicate that the unit is on. button repeatedly to select " " source. Select a station using one of the following methods. Manual Tuning Repeatedly press the , (H, G) buttons to move from frequency to frequency until you find the station you want. Auto Tuning Press and hold the , (H, G) buttons for 2 second or more, the frequency changes down, or up, automatically until a station is found. Adjust volume using the volume control knob on the front of the unit or +/- buttons on the remote. button on the remote in playing mode, all sound will be muted. Press the the button again or +/- buttons on the remote or rotate the volume control knob on the front of unit to resume sound. Presetting Stations 1. [. . . ] (AC Operation) Reasons AC/DC adapter isn't plugged into a wall outlet or the connector isn't plugged into the power supply jack on the back of the unit. Wall outlet is not functioning Solutions Plug the AC/DC adapter into a wall outlet and plug the connector into the power supply jack on the back of the unit. Plug another device into the same outlet to confirm the outlet is working. Connect the AC/DC adapter to the unit for charging. [. . . ]