User manual VIEWSONIC PJ256D

[. . . ] ViewSonic PJ256D DLP Projector ® - User Guide - Guide de l'utilisateur - Bedienungsanleitung - Guía del usuario - Guida dell'utente - Guia do usuário - Användarhandbok - Käyttöopas - Py - - Compliance Information For U. S. A. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) The device may not cause harmful interference, and (2) this device must accept any interference received, including interferencee that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] If you wish to turn the projector back on, you must wait until the projector has completed the cooling cycle and has entered standby mode. Once in standby mode, simply press "Power/ Standby" button to restart the projector. Disconnect the power cord from the electrical outlet and the projector. Do not turn on the projector immediately following a power off procedure. Warning Indicator When the "TEMP" indicator turns red, it indicates the projector has overheated. The projector will automatically shut itself down. When the "LAMP" indicator flashes red (0. 5 second intervals), it indicates a problem with the lamp. Turn off the projector and disconnect the power cord from the electrical outlet, then contact your local dealer or our service center. When the "LAMP" indicator flashes red (1 second intervals), it indicates the fan failed. Stop using the projector and disconnect the power cord from the electrical outlet, then contact your local dealer or our service center. ViewSonic PJ256D 12 Adjusting the Projected Image Adjusting the Projector Image Height The projector is equipped with an elevator foot for adjusting the image height. To raise the image: 1. Raise the image to the desired height angle , then release the button to lock the elevator foot into position. Lower the image, then release the button to lock the elevator foot into position. Use to fine-tune the display angle. 1 Elevator Button 3 2 Elevator Foot ViewSonic PJ256D 13 Adjusting the Projector Zoom / Focus You may turn the zoom lever to zoom in or out. To focus the image, rotate the focus ring until the image is clear. The projector will focus at distances from 4. 9 to 32. 8 feet (1. 5 to 10. 0 meters). Zoom Lever Focus Ring Adjusting Projection Image Size Diagonal 123. 0" (312. 5cm) 172. 2" (437. 5cm) 246. 1" (625. 0cm) 196. 9" (500. 0cm) 73. 8" (187. 5cm) 36. 9" (93. 8cm) 31. 7" (80. 5cm) 63. 4" (160. 9cm) 105. 6" (268. 2cm) 147. 8" (375. 5cm) 169. 0" (429. 2cm) 211. 2" (536. 5cm) 4. 92'(1. 5m) 9. 84'(3. 0m) 16. 40'(5. 0m) 22. 97'(7. 0m) 26. 25'(8. 0m) 32. 81'(10. 0m) Screen (Diagonal) Screen Size Max. Max. (WxH) Min. (WxH) 36. 9"(93. 8cm) 31. 7"(80. 5cm) 29. 52" x 22. 14" (75. 0 x 56. 3cm) 25. 36" x 19. 02" (64. 4 x 48. 3cm) 4. 92'(1. 5m) 73. 8"(187. 5cm) 63. 4"(160. 9cm) 59. 04" x 44. 28" (150. 0 x 112. 5cm) 50. 72" x 38. 04" (128. 7 x 96. 5cm) 9. 84'(3. 0m) 123. 0"(312. 5cm) 105. 6"(268. 2cm) 172. 2"(437. 5cm) 147. 8"(375. 5cm) 196. 9"(500. 0cm) 169. 0"(429. 2cm) 246. 1"(625. 0cm) 211. 2"(536. 5cm) 196. 88" x 147. 66" (500. 0 x 375. 0cm) 168. 96" x 126. 72" (429. 2 x 321. 9cm) 32. 81'(10. 0m) 98. 40" x 73. 80" 137. 76" x 103. 32" 157. 52" x 118. 14" (250. 0 x 187. 5cm) (350. 0 x 262. 5cm) (400. 0 x 300. 0cm) 84. 48" x 63. 36" 118. 24" x 88. 68" (214. 6 x 160. 9cm) (300. 4 x 225. 3cm) 16. 40'(5. 0m) 22. 97'(7. 0m) 135. 20" x 101. 40" (343. 4 x 257. 5cm) 26. 25'(8. 0m) Distance This graph is for user's reference only. ViewSonic PJ256D 14 Control Panel & Remote Control There are two ways for you to control the functions: Remote Control and Control Panel. Control Panel Remote Control Using the Control Panel Power/Standby 4 Refer to the "Power On/Off the Projector" section on pages 11-12. Source 4 Press "Source" to choose RGB, Component-p, Component-i, S-Video, Composite Video and HDTV sources. Menu 4 Press "Menu" to launch the on screen display (OSD) menu. Keystone To exit OSD, press "Menu" again. / 4 Adjusts image distortion caused by tilting the projector (±8 degrees). Four Directional Select Keys 4 Use your selection. Enter Re-Sync to select items or make adjustments to 4 Confirm your selection of items. 4 Automatically synchronizes the projector to the input source. ViewSonic PJ256D 15 Using the Remote Control Power 4 Refer to the "Power On/Off the Projector" section on pages 11-12. Source 4 Press "Source" to choose RGB, Component-p, Component-i, S-Video, Composite Video and HDTV sources. Auto 4 Automatically synchronizes the projector to the input source. Keystone 4 Adjusts image distortion caused by tilting the projector (±8 degrees). Press "Keystone" button, then use setting. to adjust the Hide 4 "Hide" immediately turns the screen black. Press "Hide" again to restore the displayed image. Laser Button 4 Aim the remote at the viewing screen, press and hold this button to activate the laser pointer. Freeze 4 Press "Freeze" to pause the screen image. Remark : "*" this is computer mode only. And these functions are only available when the projector is connected to a computer via an USB cable. Mouse/Mouse Right Click/Mouse Left Click (*) 4 These functions are the same as a mouse of PC or Mac. Four Directional Select Keys 4 Use Enter your selection. to select items or make adjustments to 4 Confirm your selection of items. Menu 4 Press "Menu" to launch the on screen display menu. To exit OSD, press "Menu" again. ViewSonic PJ256D 16 On Screen Display Menus The Projector has multilingual On Screen Display menus that allow you to make image adjustments and change a variety of settings. The projector will automatically detect the source. How to operate 1. [. . . ] Damage, deterioration or malfunction resulting from: a. Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or failure to follow instructions supplied with the product. Repair or attempted repair by anyone not authorized by ViewSonic. Any damage of the product due to shipment. [. . . ]