User manual VIEWSONIC WPG-350

[. . . ] ViewSonic WPG-350 ® - User Guide - Guide de l'utilisateur - Bedienungsanleitung - Guía del usuario Wireless Presentation Gateway - Model No. : VS12526 Compliance Information FCC Statement This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. [. . . ] To use Quarter Split Function, please login to WPG, and select a key (1 to 4) to present: Number 1 to 4 correspond to different area of display screen: 1 3 2 4 When you click a number, your content will be displayed in corresponding Quarter-Split display area To show content in full-screen mode, simply click `Play' button; to resume to Quarter-Split display, simply click number key 1 to 4. NOTE: When `Presentation Lock' is checked, no one will be able to interrupt a progressing presentation. 31 ViewSonic WPG-350 Chapter V Configure WPG 5-1 Conference Control When there is more than one presentation login to WPG, you can control the content from different presenter via Conference Control webpage. Use the web browser to connect to the IP address of WPG (Wireless / Wired IP address). WPG's IP address can be found at the lower-left corner of Instruction page (refer to chapter 2-1). Click `Conference Control' from WPG's web user interface. All users currently logged in will be displayed here. To select a user's display content in certain area of Quarter-Split Display, click number 1 to 4; to display in full-screen, click button of the presenting user. To stop a progressing presentation, click 32 ViewSonic WPG-350 To select user by remote controller: When there is more than one connected application software, you can also use remote controller to select one of them to display the content (same as `Conference control' function described in last chapter). Press `Login' button on remote control. You can use `Prev. ' and `Next' button on the remote controller to move the bar, then click button to select the presenting user. 33 ViewSonic WPG-350 5-2 Connect to Web Configuration Menu Use the web browser to connect to the IP address of WPG (Wireless / Wired IP address). WPG's IP address can be found at the lower-left corner of Instruction page (refer to chapter 2-1). Click `Administrator Login' link on the left. Please input `admin' as username. For 1st time login you don't have to input password, just click `OK' to continue. If you set password before, please input password in `Password' field. 34 ViewSonic WPG-350 5-3 Status & Info Displays system information, like system software version and IP address. Many useful information can be obtained here when you need help about system configuration and firmware upgrade. 5-4 Network Settings 35 ViewSonic WPG-350 Displays and configures the network settings. Item Obtain an IP address automatically Use the following IP address DNS Server Description WPG will obtain an IP address from DHCP server automatically. Fill the fields below to setup IP address. Please input the IP address of the DNS (Domain Name Service) server. Click `Apply' button to save the settings. NOTE: When the configuration settings are changed, you must restart the network connection. You can restart the network connection by clicking "Restart" on the web configuration menu. 36 ViewSonic WPG-350 5-5 Wireless Settings Configures wireless network settings. 5-5-1 `Basic' Settings 37 ViewSonic WPG-350 Displays and configures the wireless settings. Item Wireless Function Mode Band Description Select `Enable' to enable wireless network function; `Disable' to disable it. Only AP (Access Point) mode is supported. Available options are: 2. 4GHz (B) - 802. 11b clients only. 2. 4GHz (N) - 802. 11 Draft-n clients only. 2. 4GHz (B+G) - 802. 11b and 802. 11n clients. 2. 4GHz (B+G+N) - 802. 11b, 802. 11g, and 802. 11n clients. Device Name (SSID) Channel Number Associated Client Input the Device Name of presentation gateway here. [. . . ] Microsoft Internet Explorer 6. 0 (SP2) or higher 2. Safari Approvals Software CE, FCC, IC, UL/cUL, NCC, C-TICK, RoHS-compliant Wireless Presentation Gateway software application 54 ViewSonic WPG-350 Support Format Support Format (For Windows) Category MPEG4 AVI H. 261 H. 263 Microsoft MPEG-4 v1/v2 MPG MPEG ISO MKV WMV ASF MPEG1 MPEG1 MPEG1 MPEG4 WMV7** WMV8** WMVA1**, WMVA2** PCM, ADPCM Format Video Audio* * Audio: Does not support AAC and MP3 ** Supported by Windows Media Player 10 or above Support Format (For MAC) Category Format Video Audio* MPEG4 PCM, ADPCM AVI * Audio: Does not support AAC and MP3 55 ViewSonic WPG-350 6-2 Troubleshooting Scenario: Can't connect to wireless presentation gateway Solution: 1. Check the LED lights located at the front of WPG. If `Power' LED does not light, do the following check: Check the connection of A/C adapter, and if the electrical outlet you used with A/C adapter is functioning properly. [. . . ]