User manual VISONIC POWERMAX PRO

[. . . ] POWERMAX PRO Fully Supervised Wireless Alarm Control System Installer Guide TABLE OF CONTENTS 1. INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2. 1 General Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2. 2 RF Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2. 3 Electrical Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2. 4 Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2. 5 Physical Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 4. 4. 21 "Not Active" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If the method defined to report events in the 1st priority fails, the control panel will attempt to report using the method defined in the 2nd priority (see notes in 1st Report Method). The options are: disable, cellular, broadband and PSTN. 3rd Report Method [Fig 4. 5. 3(4)] Here you define the 3rd priority of method used to report events. If the method defined to report events in the 2nd priority fails, the control panel will attempt to report using the method defined in the 3rd priority (see notes in 1st Report Method). The options are: disable, cellular, broadband and PSTN. Dual Reporting [Fig 4. 5. 3(5)] Here you determine whether to report events using PSTN and cellular at the same time instead of waiting for the 1st method to fail before trying the 2nd method. The options are: disable, PSTN & broadband, PSTN & cellular and broadband & cell. 4. 5 Here you enter the number that will identify your specific alarm control system to the 1st central station. The number consists of 6 hexadecimal digits. 4. 5 Here you enter the number that will identify your system to the 2nd central station. The account number consists of 6 hexadecimal digits. PSTN/GSM RCVR1 [Fig 4. 5. 3(8)] - see note in Fig. 4. 5 Here you program telephone number of the 1st central station (including area code, 16 digit max) to which the system will report the event groups defined in Report Events. PSTN/GSM RCVR2 [Fig 4. 5. 3(9)] - see note in Fig. 4. 5 Here you program telephone number of the 2nd central station (including area code, 16 digit max) to which the system will report the event groups defined in Report Events. IP RCVR 1 [Fig 4. 5. 3(10)] Here you enter the IP address of the IP receiver that is located in the 1st central station. IP RCVR 2 [Fig 4. 5. 3(11)] Here you enter the IP address of the IP receiver that is located in the 2nd central station. SMS RCVR 1 [Fig 4. 5. 3(12)] Here you enter the telephone number of the SMS receiver that is located in the 1st central station. SMS RCVR 2 [Fig 4. 5. 3(13)] Here you enter the telephone number of the SMS receiver that is located in the 2nd central station. PSTN Report Format [Fig 4. 5. 3(14)] - see note in Fig. 4. 5 Here you select the reporting format used by the control panel to report events to central stations. The options are: SIA text Contact-ID SIA 4/2 1900/1400 4/2 1800/2300 Scancom (see Appendix C - code lists). 20 D-302541 4/2 Pulse Rate [Fig 4. 5. 3(15)] - see note in Fig. [. . . ] Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so these limitations may not apply under certain circumstances. The Manufacturer shall be under no liability whatsoever arising out of the corruption and/or malfunctioning of any telecommunication or electronic equipment or any programs. The Manufacturers obligations under this Warranty are limited solely to repair and/or replace at the Manufacturer's discretion any Product or part thereof that may prove defective. Any repair and/or replacement shall not extend the original Warranty period. [. . . ]