User manual VITEK VT-PTZ

[. . . ] VT-PTZ Series Xpress Dome with 18x, 26x or 36x Optical Zoom VITEK · True Night Shot (D/N) Function with Automatic Cut Filter (VT-PTZ26 & VT-PTZ36) · Built-in 36x Optical Zoom / 12x Digital Zoom (VT-PTZ36), Built-in 26x Optical Zoom / 12x Digital Zoom (VT-PTZ26) or 18x Optical Zoom / 12x Digital Zoom (VT-PTZ18) · Auto Protocol Detection · 248 Presets programmed with view direction, zoom, BLC. · 4 Patterns record and play back user preference of surveillance path up to 240° sec. · 16 Scans, 1 Auto Pan: 8 speed steps from slow to medium panning with smooth Vector Scan. · 8 Tours: Each tour consists up to 64 Preset, Pattern, Scan and other Tours. [. . . ] RS-422 Switch the RS-422 setting to "On" on the dip switch S4. Connect the wires to the TX+/TX- and RX+/RX- ports on the control device. Connect the TX+/TX- wires from the control device to the RX+/RX- and the RX+/RXwires to the TX+/TX- ports respectively. STAR A "Star" connection (as compared to the "Daisy Chain" connection) requires a splitter as the RS-485 native connection does not support a "Star" connection layout. Distance The maximum distance for the RS-485 connection is 1. 2 Km. Any distance exceeding 1. 2Km requires a repeater. 2. 6. 2 Alarm connection A variety of external sensors such as Magnetic contacts, PIR (motion detectors) and other circuits can be used in conjunction with the alarm input/output of the Speed Dome to various triggers. Please refer the following charts when connecting the alarm wires. Alarm A J2 1 2 3 4 5 6 ALARM A COM A NC A NO A GND ALARM 4 ALARM 3 COLOR BLACK BROWN RED ORANGE YELLOW GREEN Alarm B 20 VT-PTZ Series 7 8 ALARM 2 ALARM 1 BLUE WHITE J4 1 2 3 4 5 6 7 8 ALARM B COM B NC B NO B GND ALARM 8 ALARM 7 ALARM 6 ALARM 5 COLOR BLACK/WHITE RED/WHITE YELLOW/WHITE GREEN/WHITE BLUE/WHITe PURPLE GREY WHITE 1. COM A / COM B Connect the wire for the alarm output with either COM A or COM B, whether NC or NO circuits are used. NC A / NC B Connect the wire for the alarm output using the normally closed circuit. The Speed Dome can trigger an alarm output using a normally closed circuit to activate a variety of external devices such as sirens, buzzers or lights. NO A / NO B Connect the wire for the alarm output using the normally open circuit. GND All the ground connections to either alarm input or output must be connected to GND. 21 VT-PTZ Series 5. Alarm 1 ~ 8 Connect the wire to the appropriate alarm input. Up to eight alarm wires can be connected. 2. 7 MOUNTING THE SPEED DOME Once all the dip switches and all the wiring have been properly configured, the Speed dome can be mounted in a variety of configuration using the available accessories. The (product name here) itself should be mounted on a surface with a supporting load of 5kg (11lbs). More weight load should be put into consideration when using accessories. Ceiling mount illustration 22 VT-PTZ Series 2. 8 POWER ON AND BOOT UP SEQUENCE When the Speed Dome is twisted in and locked onto the base module, it will be powered on and will run its self diagnostic boot up sequence. It will run a series of self tests on the RAM, pan and tilt and their point of origins. 23 VT-PTZ Series If any of the diagnostic sequence is disturbed or is malfunctioning, then an error message will appear to the specific function. 2. 9 MAIN SCREEN DISPLAY Program No. Compass Direction Function Title Information Alarm Display Dome Camera Title Pan & Tilt Angle Dome Camera ID 24 VT-PTZ Series III. PROGRAMMING AND OPERATION Provided that all connections are properly made, the Speed Dome which needs to be programmed must be selected before any programming is done. Please note that the Xpress Keyboard (VT-KBD1) is required to program the Xpress Dome. All instructions below refer to the operation of the Xpress Keyboard. Press the number for the camera, and then press the CAM button sequentially to select a specific camera. [. . . ] The utility is accessed using a keystroke combination. The utility provides settings for camera functions, zoom, alarms, text display, and password protection. PATTERN A series of pan, tilt, zoom and focus movements from a single programmable dome. Up to 8 patterns may be programmed for the dome camera. [. . . ]