User manual VITEK VTC-C770WDR

[. . . ] VTC-C770WDR WDR True Day and Night (ICR) Camera VITEK · Pixim D8800C Seawolf Digital Imaging System CMOS · 700TVL High Resolution · On Screen Display (OSD) Menu · 3DNR - Three Dimensional Motion Adaptive Noise Reduction · UTC CONTROL - Serial Control over Coax · 0. 00008 Lux (F1. 2@40IRE using sense-up) · Supports C/CS mount DC drive lenses · Supports NTSC & PAL Standards · 4:3 / 16:9 Ratio Scaled Video Output · CRT / LCD Selectable Video Output Optimization · 10 - bit ITU DSP · 4 Metering Zones for WDR Optimization VTC-C770WDR WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. The symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the unit. The symbol is intended to alert the user to the presence of un-insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to person. Caution To prevent electric shocks and risk of fire hazards, do NOT use other than specific power source. Warning (NTSC version) -- This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their own expense. Caution -- Any changes or modifications in construction of this device that are not expressly approved by the party responsible for compliance, could void the user's authority to operate the equipment. 1 VTC-C770WDR Table of contents 1. [. . . ] Steps 3, 4, 5 and 7 may need to be repeated several times to obtain the best results 8. Tighten Back focus Adjustment Lock Screw again 5. 3. Installation The camera has a 1/4" thread insert on its top and bottom side for mounting the camera to a tripod, wall or ceiling with a corresponding mount. 5. 4 Commissioning · First, connect the power supply to the power terminal on the rear panel of camera · Second, plug the power adaptor to the main supply · Power indicator LED will be lit · The camera is ready for operation 5. 5. Power Supply Connections The camera can work with either 24VAC or 12VDC, dual voltage power. It does NOT require the polarity-matched connection for 12VDC supply. Primary and secondary grounds are completely isolated to avoid the possible ground-loop problems. Its wide operating voltage range of 10. 5V-30V for DC and 12-28. 8V for AC gives extra flexibility at the installation. 6. Start up When the camera is powered properly, it starts up by initializing the internal parameters and the filter switch mechanism. The filter switch unit repeats IN and OUT at each power up and just after RESTORE FACTORY SETTINGS. 7 VTC-C770WDR 7. SETUP 7. 1 In the menu Use , buttons to move the menu, button to select or enter. 7. 2 Entering menu Press 7. 3 MAIN Follow the chart below for submenu settings button longer for than 2 seconds on the back of the camera. , buttons to change the settings and press MENU EXPOSURE Default Descriptions Sets COLOR ROLL COMP. , AE PREFERENCE, WDR CONTROL and SENSE-UP. Sets OFF, AUTO or NIGHT OFF ­ Day/Night is disabled and camera works as a normal color camera. AUTO ­ Camera switches DAY from/to NIGHT automatically. N->D THRES, N<->D DELAY, BURST ON B/W can be set. See DAY&NIGHT AUTO SETUP for detail. NIGHT ­ Forced to remove IR cut filter and switch to B/W. In sub-menu, Accurate Focus can be set by function of FOCUS ADJ. . . COLOR SELECT, SHARPNESS, VIDEO DAY/NIGHT AUTO 3D NR LENS SELELT PICTURE CONTROL SPECIAL D-EFFECT EXIT DC Sets MOTION, PRIVACY MASK, STANDARD, RS485 CONTROL. Sets FREEZE, FLIP or D-PTZ. SYNC, LANGUAGE, Choose EXIT, SAVE AND EXIT or FACTORY SET. 8 VTC-C770WDR 7. 4 EXPOSURE To enter EXPOSURE menu, press button at MAIN>EXPOSURE. EXPOSURE EXPOSURE Default Descriptions Descriptions In NTSC system, the entire color tone on the monitor may continuously <WDR MID> Medium level ofreddish and greenish. the dynamic range control for each PRESETs. [. . . ] To exit MOTION ZONE SETUP, press button for 2 seconds. 13 VTC-C770WDR 7. 9. 2 PRIVACY AREA Up to 6 privacy areas can be programmed in size, position and mask color. Use joystick to change size, position and mask color. Right after pressing button at ON, the 1st zone appears on top-left corner in orange. The orange colored zone can be relocated in its location with , , , buttons. Image after pressing button again. (1st zone changes to blue) Blue colored zone can be resized with , , , buttons. An example of the mask when resizing with , Press , , buttons An example of mask when relocating. button longer than 2 seconds to return to the previous menu. 14 VTC-C770WDR 7. 9. 3 RS485 CONTROL RS485 CONTROL CAMERA ID ID DISPLAY PROTOCOL BAUD RATE Default 1 OFF VITEK 2400 Description Determines the camera's identification (between 1 and 255) Displays camera title on top-left corner of the screen. [. . . ]