User manual VITEK VTM-14C-H

[. . . ] 4) Follow Instructions All operating and use instructions should be followed. 5) Cleaning Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Exception: A product that is meant for uninterrupted service and that for some specific reason, such as the possibility of the loss of an authorization code for a CATV converter, is not intended to be unplugged by the user for cleaning or any other purpose, may exclude the reference to unplugging the product in the cleaning description. [. . . ] For products intended to operate from battery power or other sources, refer to the operating instructions. 12) Grounding or Polarization This product is equipped with a three-wire grounding-type plug a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug. 13) Power-Cord Protection Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. 14) Protective Attachment Plug The product is equipped with an attachment plug having overload protection. See instruction Manual for replacement or resetting of protective device. If replacement of the plug is required, be sure the service technician has used a replacement plug specified by the manufacturer that has the same overload protection as the original plug. 15) Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and builtup static charges. Article 810 of the National Electrical Code. The POWER LAMP above the switch will illuminate. POWER LED LAMP Power lamp indicates the power is on. REAR PANEL A/V INPUT/OUTPUT: AC INPUT Use 100-240V AC, 50/60 Hz. To prevent electrical shocks and fire hazards, do not use any other power source. VIDEO INPUT & OUTPUT CONNECTORS These BNC connectors permit looping of a video signal in those installations where it is desirable to display the video signal on more than one monitor. A standard 1. 0 Vp-p video signal applied to the VIDEO INPUT will also appear at the VIDEO OUTPUT. Use coaxial cables with BNC type plugs for these connections. S-VIDEO JACK If the camera or other video source outputs an S-VIDEO signal, connect it directly to this jack. AUDIO INPUT & OUTPUT CONNECTORS Connect an RCA cable between these jacks and the audio output jack of a camera or VCR. 5 OSD MENU ADJUSTMENTS Access the OSD Menu: Press the MENU button and use the arrow up/down buttons and arrow left/right to navigate the menu system. To exit the OSD menus, press MENU repeatedly until the menu closes. Contrast adjustment: Adjust the CONTRAST control for the desired overall display contrast. Proper adjustment will allow maximum gradations between the darkest and lightest picture areas. [. . . ] Preset operation: To move the cursor with the arrow up/down buttons and enter the next page by pressing the arrow left/right buttons. When pressing the arrow left/right buttons, change adjustment value to factor condition. 6 CONNECTING THE MONITOR Video camera Audio Audio signal cable Video Video signal cable VCR Audio Video Video Monitor Video camera Audio Audio signal cable Video Video signal cable VCR Audio Video Video Monitor Video camera Audio Audio signal cable VCR Audio Y/C (S-VHS) S-VHS Signal cable 7 NOTES 8 NOTES 8 SPECIFICATIONS DETAILED SPECIFICATIONS Picture Tube Resolution Video System A/V Terminals Input Signal Sound output Speaker Power Source Power Consumption Operating Temperature Dimensions(W x H x D) Weight 14" diagonal with 90° deflection angle 450 TV Lines NTSC / PAL Looping BNC Video In/Out, S-Video Input, Audio In/Out Video Composite: 1Vp-p 1. 0 W 3W AC 100-240V~, 50/60 Hz 45 Watts 32°-106° F (0°-40° C) 13. 8" x 12. 9" 14. 6" (350 x 328 x 371 mm) 30. 9 lb (14Kg) 10 WARRANTY INFORMATION LIMITED LIABILITY WARRANTY VITEK monitors carry a two (2) year limited warranty FOB VITEK warehouse, except for CRT Monitors (picture tube) which carry a ninety (90) day warranty due to potential misuse. VITEK warrants to the purchaser that products manufactured by VITEK are free of any rightful claim of infringement or the like, and when used in the manner intended, will be free of defects in materials and workmanship for a period of two (2) years, or as otherwise stated above, from the date of purchase. VITEK'S obligation under this warranty shall be limited to the repair, including all necessary parts and cost of labor connected therewith, or at its option, the exchange or a credit issued towards the purchase price of any video equipment which shows evidence of a manufacturing defect within the warranty period. [. . . ]