User manual VITEK VTM-LCD203P

[. . . ] The user may find the following booklet prepared by the Federal Communications Commission helpful: HOW TO IDENTIFY AND RESOLVE RADIO-TV INTERFERENCE PROBLEMS. This booklet is available from the US Government Printing Office, Washington, DC 20402, Stock Number 004-000-00345-4 1) Read Instructions All the safety and operating instructions should be read before the appliance is operated. 2) Retain Instructions The safety and operating instructions should be retained for future reference. 3) Heed Warnings All warnings on the product and in the operating instructions should be adhered to. [. . . ] e) If the product has been dropped or damaged in any way, and f) When the product exhibits a distinct change in performance this indicates a need for service. 22) Replacement Parts When replacements parts are required, be sure the service technician has used replacements parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may results in fire, electric shock or other hazards. 23) Safety Check Upon completion of any service or repairs to this receiver, ask the service technician to perform safety checks to determine that the product is in proper operating condition. 24) Wall or Ceiling Mounting The product should be mounted to a wall or ceiling only as recommended by the manufacturer. 25) Heat The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. 3 TABLE OF CONTENTS Safety Instructions . 4 Parts Description - Front Panel Controls . . 7 OSD Menus - OSD Menu Index (Video Mode) . . 11 - Sound Menu (Video & PC Mode) . . 14 VESA Wall Mount / Extension Arm Installation . . 19 4 FRONT PANEL CONTROLS 1 2 3 4 5 1 2 3 4 5 VIDEO The VIDEO button changes the video input source. Menu The MENU button turns the On Screen Display (OSD) on/off and is used to enter/exit sub-menus. VOL (Volume) The VOL button controls the volume of the sound and is used to adjust values within the OSD menus. SEL (Select) The SEL button navigates through the OSD menus. POWER The POWER button turns the monitor on and off. 5 REAR PANEL CONNECTIONS 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 6 HEADPHONE Audio output for use with devices that utilize a 3. 5mm interface including: headphones, PC speakers, and computers. DVD IN Analog Y, Pb, Pr component video input. DVD AUDIO Stereo RCA audio input enabled while DVD Input is enabled. A/V IN RCA Video and Stereo RCA audio input. The audio input also accepts a mono signal when connected only to the Left channel. This audio input is also enabled while the S-VIDEO input is selected. S-VIDEO S-Video input for use with devices that utilize a S-Video interface including: S-VHS VCRs and computers. PC AUDIO IN Audio input for use with devices that utilize a 3. 5mm interface including: computers and music players. DC 15V Connects the included 15V DC power supply. VIDEO Looping BNC composite video input/output for use with devices that utilize a BNC video connection interface including: analog and digital recorders, multiplexers, quads, and switchers. CONNECTING TO A VIDEO SOURCE BNC VIDEO CONNECTION (#9 on Previous Page) 1) Connect a coaxial BNC cable between the BNC VIDEO IN on the monitor and the OUT terminal on the device. An additional device (monitor, recorder, ETC. ) can be connected via VIDEO OUT. 2) Connect a set of RCA audio cables between the A/V-IN (L, R) on the monitor and the out terminals on the device. Below are the OSD Menus and Sub-Menus while using the PC Input. [. . . ] Replacement parts furnished in connection with this warranty shall be warranted for a period equal to the UN-expired portion of the original equipment warranty. This warranty shall not apply to repairs or replacements necessitated by any cause beyond the control of VITEK, including but not limited to, acts of nature, improper installation, misuse, lack of proper maintenance, accident, voltage fluctuations, and unauthorized repairs or modifications. This warranty becomes VOID in the event serial numbers are altered, defaced, or removed. Shipping charges, if any, must be prepaid. [. . . ]