User manual VOSS MYR1150-AL

[. . . ] 11 Stainless steel surfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 The wok . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Something not working . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Service and spareparts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Do not use the wok if it is damaged in any way, contact your local AEG Service Centre. Never use plastic or aluminium dishes on the wok. Never leave the wok unattended while deep fat frying, or heating fats and oils. Disposal Make the wok unusable by cutting off the cable. Dispose of any packaging material and old appliances at an authorised disposal site. 4 Description of the product Burner Knob Placement of grid Guide pins for grid 5 Operating instructions Burner markings Off. flame The operating knob has a ring showing the scale of markings. 6 Burner cover/burner ring Together with the burner ring the burner cover forms a space where the final mixture of gas and air takes place in order to make the gas burn correctly. Please note: It is consequently very important that the burner cover/ring is placed correctly on the burner. The burner ring has been provided with holes for the ignition electrode, and the thermo sensor. If the burner cover/ring are wrongly placed the burner will operate incorrectly, and the burners may be damaged within at short space of time. Burner ring Burner cover Correct Wrong Ignition electrode (A) The burner has been provided with an ignition electrode. As long as the operating knob is depressed, the automatic ignition will ensure that a spark is emitted between the ignition electrode and the burner cover. Burner Main nozzle Burner ring Burner cap Thermo Sensor (B) The hob unit features fully-secured gas taps (thermo-fuse) In case the flame goes out, the thermo sensor automatically prevents gas admission after a few seconds (max. Note: Gas admission is always allowed while the operation button is pressed See start-up procedure Ignition electrode (A) Thermo Sensor (B) 7 The wok-unit has a special pan support which enables use of a wok pot with curved bottom. nominal load Q, HS: Wok burner = 3, 9 kW x 1 Total= 3, 9 kW FSD The unit features fully-secured gas taps (thermo-fuse). HS = Gross calorific value Q = Nominal load Voltage= Ignition transformer= CE 048 AT- 0030 Radio-noise reduction This unit observes the current EEC-directive on radio noise reduction. This gas appliance is -approved and marked in accordance with the gas appliance Directive (90/396/CEE), the low voltage directive (73/23/CEE) and the EMC directive (89/336/CEE incl. 220-240 V AC 50 HZ - 0, 6 VA N L1 240 V 1N + PE The hob must be connected via an external switch with a contact gap of min. 3 mm (the main switch may be used) Cable type: 0, 75 mm² HO5VV-F 12 Important safety requirments This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). Detailed recommendations are contained in the following British Standards Codes Of Practice: B. S. The hob should not be installed in a bed sitting room with a volume of less than 20 m³. If it is installed in a room of volume less than 5 m³ an air vent of effective area of 110 cm² is required. If it is installed in a room of volume between 5 m³ and 10 m³ an air vent of effective area of 50 cm² is required, while if the volume exceeds 11 m³ no air vent is required. However, if the room has a door which opens directly to the outside no air vent is required even if the volume is between 5 m³ and 11 m³. If there are other fuel burning appliances in the same room, B. S. [. . . ] Check the fuse and replace if necessery. When the operating knob is released the gas ring goes out again The operating knob has not been depressed long enough, or has not been depressed sufficiently. Ensure the cover has been replaced correctly, e. g. after cleaning. The gas ring burns unevenly If after all these checks, your hob still does not operate correctly, contact your local AEG Service Force Centre. In-guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown. [. . . ]