User manual VOYAGER VOM-783T

[. . . ] * Low level and high level inputs for radio and TV for convenience. * Mode indicator LED's on front panel. * Sleep mode (ultra-low current draw mode) after 2 minutes with no signal detected. * All controls factory preset with recessed knobs. [. . . ] These spatial cues are restored by the use of Head Related Transfer Functions (HRTFs) , which process ambient sounds via patented frequency response correction curves. Stereo has a narrow sweet spot SRS 3D Sound expand the stereo sweet spot 1998 SRS Labs, inc. SRS, the SRS logo, Sound Retrieval System are registered trademarks of SRS Labs, Inc. All other corporate and brand names are trademarks of their respective holders. ----- 3 ----- SRS1000 Theater Sound Owner's Manual < Index > 1. Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p1 2. Front/Rear Panel Description . . . . . . . . . . . . . . . . . . . . . . . . . p2 3. System Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p4 4. Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p5 5. Specification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p7 SRS1000 Theater Sound Owner's Manual Package Contents 1. SRS1000 Amplifier. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1pc ATE R Min Ma x Min Ma x Min Ma x TV Ga in 3D -F iel Vo y Ra dio Ga in d TV Ra dio 100 3-B Hz AN Min Ma x Min Ma x Min Ma x age r D EQ 1kH 2. Wire Harness - 16 pin - Main Connection . . . 1pc 3. Wire Harness - 8 pin - Radio High Level (Speaker Input ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1pc R THEATER SOUND SRS1000 4. Doing so would cancel the SRS 3D effect. - Black Blue + - Car Battery Trigger switch Car Battery DC +12V Brown/White + RF Gray Gray/Black White + + White/Black LF Voilet Voilet/Black RR Green Green/Black + - - LR TV Note: Connect Low Level input or High Level input for each device (Radio/TV), not both. The unused input for device should have no connection. ----- 4 ----- SRS1000 Theater Sound Owner's Manual Operation Connecting the speakers 1. Speaker impedance a) Front & rear speakers : 4 minimum b) Subwoofer1 & Subwoofer 2 speaker: 4 minimum 2. Be sure to connect the cords between the speaker terminal and speaker systems with the same polarities(''+'' to ''+'' , ''-'' to ''-'' ), if not, the central sound will be weak and the effect of the different instruments will not be clear. When connecting the speakers, be sure that the wires do not stick out from the terminals and touch other terminal or the rear panel!a) Be sure all connections are made correctly before applying power to the main unit. Damage to the unit may result if not connected properly. b) Check the polarity (positive and negative ) of connections and the directivity of stereo separation (right cord to right channel terminal) First Time Operation Important: Before Applying Power: a) Set all controls on SRS1000 to mid position (slot in knob will be vertical). b) Be sure TV mode trigger is not active (ie: 0 VDC) c) Be sure that TV and Radio are off System Set-Up (Gain Matching, EQ setting, 3D Effect setting) 1) Apply power to SRS1000. Verify Radio mode by checking Radio/TV indicators on Front Panel. [. . . ] As a gengeral rule of thumb, the smaller the vehicle, the more 3D effect is needed to simulate the full "theater experience". For the most part, however, this adjustment is mostly according to personal taste. ----- 6 ----- SRS1000 Theater Sound Owner's Manual Specifications: 1. rating) : Front channel : 15w+15w (4 ) Rear channel : 15w+15w (4 ) Subwoofer channel : 25w+25w (4 ) 2. THD: Front channel : 0. 3% Rear channel : 0. 3% Subwoofer channel : 0. 5% 3. [. . . ]