User manual VOYAGER VOM-78T

[. . . ] Yellow/Red from harness to RR+ of radio 2. Yellow from harness to LR+ of radio NOTE: Negative connections are not required on the input. 4) VCP Installation a) VCP can be mounted in the following methods: 1. Obtain ASA " soft mounting kit" P/N 1401250. [. . . ] h) If required, place the wedge base in position. Place mounting bracket in position and assemble washer, lock washer, and nut to hold bracket in position. i) Slide monitor into position and hand tighten two ¼-20x1" bolts to hold monitor in position. Adjust hardware combination to achieve optimal viewing position. (Fig. 10) j) Connect video in/out (6-pin connector) and power (4-pin pigtail). Splice two 14G orange from harness to one 14G orange from pigtail, connect two 14G black from harness to one 14G black from pigtail, connect two 18G blue/white from harness to 18G blue/white of pigtail. k) Install remaining ¼-20 grade 8 bolts and tighten all four to 100 in. l) Clean four tabs of mounting bracket with a 70% solution of isopropyl alcohol. m) Place two 1" x 1" and 1"x 2'pads of " dual lock"velcro on mounting bracket. 10) n) Place padded shroud over monitor assembly and locate position of mating velcro pad. If a 10°wedge base is used, be sure shroud is flush to all edges prior to attaching velcro. Spkr (+) IR (+) IR (-) Monitor Trigger Ground Audio From VCP (-) Figure 4 1) MIC Gain- These controls are accessed through the control in rear. The potentiometer marked GAIN1 sets the level for the MIC jack, and GAIN2 sets the level for the second MIC jack. These adjustments will be required to match audio levels of the other sources. To adjust: a) Turn the VOM-78T to the " position and turn the volume control to half on" volume and select Video or Radio on the source select control. b) Be sure the video or radio source is operational to obtain a reference level. c) Connect the hand-held MIC to rear panel. d) Key the microphone and adjust level to existing audio level produced by the selected source. Clockwise increases the audio level and counterclockwise will decrease the level. 2 & 3) Microphone 1 and 2- Microphone input plus adapter will allow operater to use most available microphones, the appropriate Gain control potentiometer must be preset per the above instructiions. 4) Speaker Out- This connection goes to both right and left internal and external speakers. 11 for speaker connections 5) Mounting Lugs- Used to level out the radio when mounting. [. . . ] SIDE SPKR 18 GRN/BLK (-) 18 GRY (+) DRIVER SIDE SPKR 4 Ohm only 18 GRY/BLK(-) 18 GRN(+) PASS. SIDE SPKR 18 GRN/BLK (-) 18 GRY (+) DRIVER SIDE SPKR 4 Ohm only 18 GRY/BLK(-) 18 GRN(+) PASS. SIDE SPKR 18 GRN/BLK (-) 18 GRY (+) DRIVER SIDE SPKR 4 or 8 18 GRY/BLK(-) Figure 11 13 Optional Video Cassette Mount P/N 1401250 (2) Clamp Brackets With 1" Foam Video Cassette Player (1) Mounting Base With 1" Foam Figure 12 14 Rear VCP Connections Figure 13 Fuse- 2 Amp Fuse Used Antenna In- External antenna hook-up Video Out- To Monitor or Video Audio Out- To Moinitor or Video RF Out- Channel 3 or 4 output to Monitor Channel Select- Selects setting for channel 3 or 4 selection, depends on area you live in. 7) Power In- Dual input for connection to barrel connector 8) DC 12V- Dual input for connection to 4-pin connector 1) 2) 3) 4) 5) 6) Front VCP Features Figure 14 1) Power- This button powers the VCP " and " . [. . . ]