User manual VTECH SBC20-2432

[. . . ] Important Safety Instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following: 1. Follow all warnings and instructions marked on the product. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. [. . . ] All system Handsets have been deregistered. To register your Handsets again, see Registration and Operation, located in the Getting Started section of the User's Manual, for details. 23 Basic Operation Note: Base ID codes are 15 digits long and can include the following characters: 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, or * . Memory Memory The Base and each Handset can store up to 50 names/numbers in memory. Each memory location can hold up to 32 digits and up to 16 characters for the name. When prompted to ENTER NAME, use the digit keys to spell the name. Each press of a particular key causes characters to be displayed in the following order: Basic Operation Number Key 1 2 3 4 5 6 7 8 9 0 Characters (in order) &', . 1 ABCabc2 DEFdef3 GHIghi4 JKLjkl5 MNOmno6 PQRSpqrs7 TUVtuv8 WXYZwxyz9 0 * # * # 24 Memory To Store a Number/Name: · Starting from the idle screen, enter the number you want to store in memory. If you make a mistake, press CLEAR to backspace. · Be sure to include long distance codes and pauses, (using the Pause softkey) if necessary. Press the MEM softkey. · You will then be prompted to ENTER NAME. Use the digit keys to 'spell' the name. If you make a mistake, press the CLR softkey. If there is space available in memory, the number/name will be saved and the Handset will return to idle mode. If the memory is full the Handset will display PHONEBOOK IS FULL and exit to the pre-dial screen without saving the entry. Follow the above procedure for storing Number/Names at the Base. The Handset and Base have separate memories. · · · 25 Basic Operation Memory To Search For and Dial a Number/Name: · Starting from the idle screen, press the MEM softkey to review memory contents. Basic Operation · Using the softkeys scroll through the memory contents in alphabetical order. · Or, you can press the FIND softkey, enter the first few chararcters of the name and then press FIND to search. If you make a mistake, press CLR softkey. The closest match, in alphabetical order, will be displayed. Once you find the entry you want, simply press a LINE key (or HANDSFREE) on the Handset or SPEAKERPHONE on the Base to dial the number. · To Delete a Number/Name: · Using steps 1 through 3 in To Search For and Dial a Number/ Name, locate the entry you want to delete. · Press the EDIT softkey. The Handset or the Base will display: 26 Memory · Press the DEL softkey. The Handset or the Base will display: To delete this record, press THIS. · · To delete all records, press ALL. To confirm the deletion of ALL records, press YES. To exit without deleting, press NO. To Edit a Number/Name · Using the steps from 1 to 3 in To Search For and Dial a Number/Name, locate the entry you want to edit. · Press the EDIT softkey twice. The Handset or the Base will display: · Select NAME or NUM. Using the softkey move the cursor to the character you want to edit and then enter the corrections as needed. [. . . ] c Testing the emergency telephone numbers you have stored is not recommended. However, if you do make a call to an emergency number: · You must remain on the line and briefly explain the reason for the call before hanging up. · Programming/testing of emergency numbers should be performed during off-peak hours, such as in the early morning or late evening, when the emergency services tend to be less busy. IC (Industry Canada) This telephone is registered for use in Canada. The term "IC:" before the radio certification number only signifies that Industry Canada technical specifications were met. Notice: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. [. . . ]