User manual VTECH VT 8100 BASE

[. . . ] Table Of Contents GETTING STARTED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Before you begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 GPL License Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Installation Directions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] You may also use settings for commonly used services in the Virtual Server table at the bottom of the screen by clicking an Edit button. Advanced Settings 26 Advanced Settings · Virtual Server: (Default Off): Click On to enable or Off to disable. This indicates whether the virtual server is initially enabled or disabled when it is created or modified. Name: Enter a name for the virtual server you are setting up. Destination IP: Enter the private IP address of the computer that is hosting the service/application. Note: It is recommended that Static IP is used as the ISP Connection Setting when Virtual Server is created. Protocol Type: Choose the type of protocol used to access your hosting service. Port: Enter a single port or a range of ports to forward to a computer on your local network. (Leave this field blank to deny access to all ports. ) · · · · 27 Advanced Settings Click Apply to save the page settings. Clicking Cancel aborts any changes you have made on the page. Advanced Settings Filters Filters allow you to restrict or permit Internet access for computers on your local network. The filter type supported on your IP 8100-2/8100-3 is IP Filter. Advanced Settings IP Filters IP filter is used to deny any specific computer from accessing the Internet using the computer's IP address. You can deny access by to specific services by port numbers or by blocking all ports for the specific computer. To add a new filter, fill in the fields above and click Apply to save the page settings. You can block access to several of the most commonly used services by clicking an Edit button in the IP Filter table at the bottom of the screen. This will copy the proper settings into the IP Filter fields. You will only need to enter the IP address of the computer to be affected by the filter (you can find this number by displaying the DHCP screen under the Admin tab). 28 Advanced Settings IP Filters: (Default to On): Click On to enable or Off to disable. This indicates whether the IP filter is initially enabled or disabled when it is created or modified. · Name: Enter a name the IP Filter you are setting up. · Destination IP: Enter the private IP address that will be affected by the filter. If left blank, any computers on your LAN will be blocked the Internet access. · Port: Enter a single port or a range of ports that will be denied Internet access. (Leave this field blank to deny access to all ports. ) · Protocol Type: Choose a protocol type to block. When finished, click Apply to add the new filter which is then listed under the IP Filter Table. [. . . ] Enter ipconfig/release to release the IP address. Enter ipconfig/renew to obtain a new address. If you are unable to obtain a valid IP address, confirm that you have a good physical connection between the computer and the IP 8100-2/8100-3. Step 4: Type, exit and then click Enter to close the Command Prompt. 47 Troubleshooting Troubleshooting I followed the Quick Start Guide for DSL, but I wasn't able to successfully configure the IP 8100-2/8100-3. [. . . ]