User manual VTECH VT 918

[. . . ] Table Of Contents INTRODUCTION . 3 PARTS CHECK LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 THE HANDSET BATTERY PACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] See STORING A REDIAL NUMBER IN MEMEORY DIAL. CHANNEL (CHAN) Key If you are experiencing noise or interference during a call, press the CHAN key to change to the next free channel. */TONE Key From the PULSE (Rotary) dialing mode, press this key to switch to TEMPORARY TONE dialing mode. When the call is ended, the phone will return to PULSE dialing mode. 12 13 NOTE: You may need to press CHAN more than once to find an interferencefree channel. VOLUME CONTROL SWITCH MEMORY (MEM) Key Press this key to enter MEMORY DIALING mode. The sequence for dialing a phone number stored in memory is: Press PHONE, MEM, Memory Location (0-9). PROGRAM/PRIVACY (PRG/PRV) Key With the Handset OFF, press this key to store phone numbers into MEMORY, as well as programming the Handset Located on the Left edge of the Handset, there are three volume controlled levels ( VOL )with respected to LOW, MEDIUM, and HIGH. HEADSET JACK (2. 5 mm) Located on Right edge of the Handset. Plug (optional) Headset into this jack for hands-free operation. See OPTIONAL HEADSET INSTALLATION AND OPERATING INSTRUCTIONS for more information. 3/6/98, 3:21 PM 918manual. pm6 12 BASE UNIT F E AT U R E S 1 PWR 2 5 8 ABC 3 6 9 DEF 4GHI 7 PRS JKL MNO IN USE TUV WXYZ CHR TONE 0OPER FLASH PRV # MUTE REDIAL HOLD MEM INT. COM SPKR VOL B A B BASE UNIT POWER (PWR) LED Glows steadily when the AC adaptor is supplying power to the Base Unit. After initialization, the CHR LED will glow steadily to indicate that the Handset battery is being charged. If the Handset is placed in the Base Unit without a battery, the CHR LED will flash rapidly with the warning beep tone. 14 13 IN USE LED Glows steadily when the Handset is on a call. Flashes in cadence with an incoming ring. HOLD LED During a phone call, whether using the Base or Handset, this LED will flash if the call is placed on HOLD. MUTE LED During a SPEAKERPHONE call, this LED will glow if the MUTE key is pressed. CHARGE (CHR) LED Blinks twice after placing the Handset in the Base Unit to indicate that initialization (assigning a new security code) has occurred. 918manual. pm6 13 3/6/98, 3:21 PM BASE UNIT F E AT U R E S Transfer the call to the Handset Return to the call by pressing SPKR. INTERCOM (INT. COM) LED Flashes rapidly when the INT. COM key is pressed. NOTE: If you have placed a call on NOTE: The Handset must be away from the Base Unit to use the INTERCOM feature. Blinks twice, accompanied by two beeps, when the Handset answer the INTERCOM call to the Base Unit. Glows steadily while the Handset and Base Unit are in INTERCOM mode. HOLD and want to hang up: Press SPKR to return to the call, then press SPKR again. FLASH KEY This key is used in conjunction with services such as CALL WAITING. SPEAKER (SPKR) LED Glows when Base Unit is in SPEAKERPHONE mode. MUTE KEY Press this key to mute the Handset microphone during a conversation. You will still be able to hear the other party, but they cannot hear you. Press MUTE again to resume two-way conversation. RINGER SWITCH Located on the right edge of the Base Unit (antenna side) 14 3 selections: HIGH, LOW, OFF MEMORY (MEM) KEY Press this key to enter MEMORY DIALING mode. The sequence for dialing a phone number stored in memory is: Press SPKR, MEM, Memory Location (0-9). 15 TONE/PULSE SWITCH Located next to RINGER switch Select mode compatible with your local telephone service (for most areas, TONE is the preferred dialing mode). PRIVACY (PRV) KEY HOLD KEY Press this key to temporarily suspend conversation without terminating the call. With a call on HOLD, you can: Intercom the Handset During a call, press PRV to prevent the Handset from joining the conversation. 918manual. pm6 14 3/6/98, 3:21 PM BASE REDIAL KEY UNIT F E AT U R E S VOLUME DOWN KEY Press this key( ) to decrease the Base Unit speaker volume. A series of rapid beeps tell you that minimum volume level has been reached. The volume level will continue to increment down if this key is held down. There are a total of 8 volume settings. When you hear a dial tone, press this key to redial the last phone number you dialed on your 918 ADX. INTERCOM (INT. COM) KEY Press this key to initiate two-way, internal communication between the Base Unit and Handset. If the Handset is in the OFF mode, it will ring a maximum of 4 times. [. . . ] Include payment for any service or repair not covered by warranty, as determined by VTECH Communications. Ship the unit via UPS Insured, or equivalent to: VTECH COMMUNICATIONS 8770 SW NIMBUS AVENUE BEAVERTON, OREGON 97008 VTECH Communications assumes no responsibility for units sent without prior ReturnAuthorization. 30 29 WHAT DOES OUR WARRANTY NOT COVER? 30 Batteries Damage from misuse, neglect, or acts of nature (lightning, floods, power surges, etc. ) Products which may have been modified or incorporated into other products Products purchased and/or operated outside the USA, its territories, or Canada. Products serviced by the owner or a service facility not expressly authorized by VTECH Communications Products purchased more than 12 months from current date Units purchased in AS IS condition, or units purchased as Distressed Merchandise. HOW DOES STATE LAW RELATE TO THIS WARRANTY? [. . . ]