User manual VTECH VT 92-9110

[. . . ] INTRODUCTION ANY KEY ANSWER 30 CHANNEL OPERATION Parts Check List: 1. Handset Base Unit Telephone line cord Locking Screw AC adapter Battery Pack 7. Wall mount bracket To purchase replacement battery packs, call VTECH Communications at 1-800-595-9511. In Canada, call VTECH Electronics at 1-800267-7377. 92-9110 TWO TONE DESIGN USER'S MANUAL HANDSET BASE UNIT TELEPHONE LINE CORD LOCKING SCREW AC ADAPTER MHz VTECH TELECOMMUNICATIONS LTD. [. . . ] CALL 1-800-595-9511 6 OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS TONE/PULSE Setting If you have touch tone service on phone line. Press PROG, , , MEM to switch to TONE dialing. If you have rotary service, press PROG, , # , MEM to switch to PULSE. NOTE: Your VT9110 is preset at the factory for TONE dialing. · Press 5 to turn off the ringer · Press the MEM key to confirm · To turn the ringer on again, see Programming the Ringer Type. Checking The Ringer To check the ringer which is currently programmed, do the following: · Press PROG · Press the # key · Press 0 · Press the MEM key to confirm Temporary Tone PHONE LED PHONE KEY OFF KEY REDIAL KEY PROG KEY VOLUME SWITCH CHANNEL KEY MEM KEY CHARGING LED IN USE LED POWER LED PAGE KEY If you have a rotary (dial-pulse) telephone service, (TONE/PULSE setting is set to PULSE), this feature allows you to enter special codes and tones to operate answering machines, use electronic banking services, calling cards, or other special services. · Press the MEM key to confirm. Answering Calls When an incoming call is ringing, the IN USE LED on the base and PHONE LED on the handset will flash. To make sure your phone rings when the handset is away from the base, please keep the base antenna in the upright position. Turning Off The Ringer To turn off the ringer on the handset, do the following: · Press PROG · Press the # key Speed Number Dialing 1. Press MEM and the memory location number key (0-9). For example, to dial the number you assigned to key '8', you would press PHONE, MEM, 8. Changing Channels If you notice interference when using your handset, press CHAN to switch to a clear channel. This function is only available when you are on a call. 8 9 OPERATING INSTRUCTIONS To Change or Replace a Speed Dial Number To change or replace a stored number in speed dial memory simply enter the new number and store it in the memory location you wish to change. For example, to change the number stored in memory position 7 to 555-1111, you would press PROG, 7, 555-1111, MEM. Press MEM IN CASE OF DIFFICULTY If you have difficulty operating your phone, the suggestions below should solve the problem. If you still have difficulty after trying these suggestions, In the US Call: VTECH Communications at 1-800-595-9511. In Canada Call: VTECH Electronics at 1-800-267-7377. · Make sure the power cord is plugged in. · Make sure the telephone line cord is plugged firmly into the base unit and the telephone wall jack. · Make sure the batteries are properly charged. If the handset makes two beeps, the batteries need charging. If the IN USE indicators do not light when you press PHONE, you must charge the batteries. · If you recently installed a new battery pack, make sure it is installed correctly. · First check all the suggestions above. · If you still don't hear a dial tone, disconnect the base unit from the telephone jack and connect a different phone. [. . . ] Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. only to the requirement that the sum of the REN does not exceed five(5. 0). Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment. [. . . ]