User manual VTECH VT1122

[. . . ] IMPORTANT SAFETY INSTRUCTIONS CAUTION TO REDUCE THE RISK OF INJURY TO PERSONS, READ AND FOLLOW THESE INSTRUCTIONS. 1 Use only the type and size batteries designed for this product. Do not dispose of the batteries in a fire. Check with local codes for possible special disposal instructions. 2 Do not open or mutilate the batteries. [. . . ] 3 "OFF" Position: This telephone does not ring with incoming calls. TELEPHONE OPERATION Repeat Calls When you receive calls repeatedly from the same caller, the display will show REPEAT adjacent to the call number of that call to indicate it is a repeat call. TELEPHONE OPERATION Storing a Phone Number One-Touch Memory Locations in the Recalling a Number from the Two-Touch Memory 1 Lift the handset. 3 Press the dial button (0-9) where you stored the number you want to call. 4 Your call will be dialed automatically. TONE* Button If you have Pulse (dial rotary) service, press this button before entering codes you may need to access remote answering systems, etc. Each button pressed after * will be sent as tone signals. The phone returns to Pulse dialing when you hang up. Blocked or Unavailable Calls 1 If the caller's telephone number is blocked (that is, the caller wishes to keep his telephone number private), the display will show PRIVATE in place of the caller name. 2 If the call is international or from an area where Caller ID service is not available, the display will show UNKNOWN in place of the caller's name. Note: We recommend that you disconnect the phone line when programming your telephone. Reviewing Calls 1 The NEW CALL indicator will flash to indicate new calls or calls that have not yet been reviewed. 3 Press DOWN to review the previous call. 4 After a new call is reviewed, it will be deducted from the total number of new calls displayed. 5 When the list of calls reaches the end, the display will display END OF LIST and return to show the current time and date in 10 seconds. MUTE Button 1 Press and hold the MUTE button when you don't want the other party to hear the conversation on your end. 2 Release the MUTE button to return to two-way conversation. TONE/PULSE Switch 1 The DP (PULSE) position is used if your local telephone system offers only Pulse (rotary dial) service or if Tone service is available but you do not subscribe to it. 2 The TT (TONE) position is used if you subscribe to Tone Dialing (DTMF) service. If you are not certain what type of service you have, check with your local telephone company. 1 Lift the handset. 3 Dial the telephone number you want to store (up to 16 digits). 4 Press the one-touch button (M1, M2, M3) where you want to store the number. When you hear the dial tone, dial the phone number you are calling using the buttons (1 to 9 and 0). The number dialed will be shown in the LCD panel. When your call is completed, hang up the handset. CALLER ID OPERATION Receiving a Call When you receive a call, your unit will display the caller information sent by the telephone company including: · The caller's name (if available) · The caller's telephone number (if available) · The date and time of the call · The Call Number to indicate the sequence of the call Note: When the memory is full and new calls are received, previous messages will be replaced by the new calls. REDIAL Button The last number you have dialed (up to 32 digits) remains in memory known as last number redial memory. If you call a number and receive a busy signal or no answer, hang up the handset. When you are ready to try the same call again, pick up the handset and tap the REDIAL button. Please note that if you have made any other calls in the meantime, only the last number you called will be stored in the redial memory. To delete an individual call: 1 Press the UP or DOWN button until the call to be deleted is displayed. 2 Press the REMOVE button twice within 1. 5 seconds. [. . . ] [For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e. g. , 03 is a REN of 0. 3). For earlier products, the REN is separately shown on the label. ] If this equipment Model# VT_1122 causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn't practical, the telephone company will notify the FCC REGULATIONS & TECHNICAL SPECIFICATIONS customer as soon as possible. [. . . ]