User manual VTECH VT9125

[. . . ] VTECH COMMUNICATIONS LTD. Distributed in the U. S. A. by VTECH Communications, Beaverton, OR Distributed in Canada by VTECH Electronics Canada Ltd. , Richmond, B. C. . Copyright 1999 for VTECH COMMUNICATIONS LTD. Printed in Malaysia 91-5081-10-00 ISSUE 0 USER'S MANUAL VT 9125 900MHz CALLER ID CORDLESS TELEPHONE IMPORTANT VTECH COMMUNICATIONS LTD. BEFORE USING YOUR NEW PHONE, WE STRONGLY RECOMMEND YOU READ THIS MANUAL THOROUGHLY. IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS Read and understand all instructions. [. . . ] Select an Index Number for the new entry (1 - 9). If you choose a number that is currently being used the old number is replaced with the new entry. The phone beeps to indicate that the new Speed Dial entry is now saved. - 12 - Using the Speed Dial List USING THE SPEED DIAL LIST REVIEWING SPEED DIAL ENTRIES You can review the entries in your Speed Dial List. You can use this method to check the contents of your Speed Dial List before you create a new entry. Press MEM OFF to clear the display. The display shows the first entry in the list. 3. Press 1 - 9 on the keypad to directly access the entry. Alternatively, press TONE or # to go through the list. DELETING A SPEED DIAL ENTRY You can erase unwanted Speed Dial entries. Find the Speed Dial entry you want to erase. Press DELETE and the Index Number of the entry. JKL In this example, you would press 5. 3. The display shows an erased record for 10 seconds. If the Index Number you press does not match the Index Number on the display, the entry is not erased. PAGING AND FINDING THE HANDSET If you ever misplace the handset, the base can help you find the location of the handset. If the handset is in use, the handset emits a tone through the earpiece. FINDING THE HANDSET 1. If the handset is lying idle, it beeps for about 3 seconds. The display shows a Paging for about 2 seconds. on the base once you have found the on the handset or handset. - 11 - Operating Your Phone USING FLASH To access your custom calling services, like Call Waiting, while you are on the telephone, press PHONE FLASH . USING TEMPORARY TONE SERVICE If you have Rotary / Pulse service, you can temporarily set your telephone to tone service for use with automated telephone services. Press TONE after you connect with the automated service. The phone automatically returns to rotary / pulse service after you hang up the call. ADJUSTING HANDSET VOLUME You can adjust the volume of the handset to LOW, MID, or HIGH by moving the switch on the side of the handset. The HIGH setting is primarily for hearing-aid compatibility. You might experience a slight decline in audio clarity when the volume switch is on HIGH. READING THE CALL TIMER The call timer starts automatically when you make or receive a call. It times the call up to a maximum of 59 minutes and 59 seconds, then starts again at zero. FINDING CLEAR RECEPTION Your phone automatically selects a channel at the beginning of the call for the best reception. If you are experiencing interference, you can either move closer to the base, or press on the handset until you CHAN find better reception. REACHING MAXIMUM RANGE The handset and base communicate up to a certain maximum range. This distance can be affected by weather, power lines, or even other cordless telephones. OUT OF RANGE If you are out of range, you may lose your call and the display will go out. [. . . ] This product is hearing-aid compatible. CAUTION Changes or modification to this device could void the user's authority to operate this equipment. - 21 - FCC Requirements This equipment has been tested and found to comply with limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ]