User manual WEED EATER XT 600

[. . . ] ENGLISH R Trademark Please do not return unit to retailer. Por favor, no devuelva el aparato al lugar de compra. Veuillez ne pas retourner l'outil au détaillant. 1-800-554-6723 www. weedeater. com Operator's Manual Manual del Operador Manuel de L'utilisateur XT 600 t IMPORTANT MANUAL - Do not throw away MANUAL IMPORTANTE - No lo descarte MANUEL IMPORTANT - À Conserver WARNING: Read and follow all Safety Rules and Operating Instructions before using this product. Failure to do so can result in serious injury. [. . . ] If symptoms occur such as numbness, pain, loss of strength, change in skin color or texture, or loss of feeling in the fingers, hands, or joints, discontinue the use of this tool and seek medical attention. An anti-vibration system does not guarantee the avoidance of these problems. Users who operate power tools on a continual and regular basis must monitor closely their physical condition and the condition of this tool. TRANSPORTING AND STORAGE trigger and the safety label on the tube. Tighten handle securely. WARNING: The shield must be properly installed. The shield provides partial protection from the risk of thrown objects to the operator and others and is equipped with a line limiter which cuts excess line. The line limiter (on underside of shield) is sharp and can cut you. S Pivot shield until bolt passes through hole in bracket. S Remove packing cover from the arbor shaft if so equipped. Thread trimmer head onto shaft; tighten securely against dust cup. Wing Nut Bracket Slot ATTACHING THE SHIELD Dust Cup Shield FUEL YOUR UNIT This engine is certified to operate on unleaded gasoline. Gasoline must be mixed with a good quality 2-cycle air-cooled engine oil designed to be mixed at a ratio of 40:1. Poulan/Weed Eater brand oil is recommended. (A 40:1 ratio is obtained by mixing 3. 2 ounces of oil with 1 gallon of unleaded gasoline). When mixing fuel follow the instructions printed on the container. Always read and follow the safety rules under FUEL SAFETY. ASSEMBLY WARNING: Make sure unit is properly assembled and all fasteners are secure. ADJUST THE HANDLE S Loosen wing nut or plastic knob on handle. S Rotate handle to upright position and tighten in a comfortable position between the STARTING Starting Position 3 HOW TO STOP YOUR UNIT Push and hold the engine stop switch in the STOP or OFF position until the unit has fully stopped. Choke lever Trigger Primer Bulb Muffler HOW TO START YOUR UNIT S Push and hold the engine stop switch in the stop/off position until the unit has fully stopped. S Remove spool by firmly pulling on tap button. S Clean entire surface of hub and spool. S Replace with a pre-wound spool, or cut two lengths of 12-1/2 feet of . 080" (2 mm) diameter Weed Eaterr brand line. Never use wire, rope, string, etc. , which can break off and become a dangerous missile. S Insert ends of the line about 1/2 inch (1 cm) into the small hole on the inside of spool. [. . . ] MANUFACTURER'S WARRANTY COVERAGE: If any emissions related part on your engine (as listed under Emissions Control Warranty Parts List) is defective or a defect in the materials or workmanship of the engine causes the failure of such an emission related part, the part will be repaired or replaced by POULAN/WEED EATER. OWNER'S WARRANTY RESPONSIBILITIES: As the lawn and garden equipment engine owner, you are responsible for the performance of the required maintenance listed in your Owner's Manual. POULAN/ WEED EATER recommends that you retain all receipts covering maintenance on your lawn and garden equipment engine, but POULAN/WEED EATER cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance. As the lawn and garden equipment engine owner, you should be aware that POULAN/WEED EATER may deny you warranty coverage if your lawn and garden equipment engine or a part of it has failed due to abuse, neglect, improper maintenance, unapproved modifications, or the use of parts not made or approved by the original equipment manufacturer. [. . . ]