User manual WESTINGHOUSE LTV-20V2

[. . . ] Avoid exposing the LCD display to moisture or high humidity. Your warranty does not cover repairs or attempted repairs by anyone not authorized by manufacturer. If your LCD Display will not be used for a long period of time, unplug and remove the batteries from the remote control. Precautions Sit at least 20" away from your LCD display. Your LCD display contains high-voltage parts. [. . . ] BASE/BS Germany. . . . . . . . . . VDE Japan . . . . . . . . . . . . . . . Electric Appliance Control Act IMPORTANT NOTICE CONCERNING POWER CORD SELECTION The power cord set for this unit has been enclosed and has been selected according to the country of destination and must be used to prevent electric shock. Use the following guidelines if it is necessary to replace the original cord set, or if the cord set is not enclosed. The female receptacle of the cord set must meet IEC-60320 requirements and may look like (Figure A1 below): Figure A1 Figure A2 For the United States and Canada In the United States and Canada the male plug is a NEMA5-15 style (Figure A2), UL Listed, and CSA Labeled. For units that are mounted on a desk or table, type SVT or SJT cord sets may be used. For units that sit on the floor, only SJT type cord sets may be used. The cord set must be selected according to the current rating for your unit. Please consult the table below for the selection criteria for power cords used in the United States and Canada. Cord Type SJT Size of Conductors in Cord 18 AWG 16 AWG 14 AWG 18 AWG 17 AWG Maximum Current Rating of Unit 10 Amps 12 Amps 12 Amps 10 Amps 12 Amps SVT FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and may cause harmful interference to radio communications if not installed and used in accordance with the instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · · · · Reorient or relocate the receiving antenna. Connect Antenna, Cable, Video, S-Video, and/or YPbPr Cables Connect video and audio cables from compatible devices to the back panel of the LCD TV. 6 4. Connect power cables Connect the power cord to the LCD TV and then to a properly grounded AC outlet. 5. Turn Power On Press the power button on the top of the LCD TV display. Or press the power button on the remote control. 7 6. Select TV as the input using the TV button (17) on the remote. Push TV/CATV button (14) to select the type of antenna or cable system attached to the TV. SCAN (6) to automatically search and remember channels. Switch channels by using the CH+ and CH- keys (11) on the remote. Use ADD/DEL (7) button to personalize the list of channels. [. . . ] If the wrong password is entered, then refer to figure 6. Figure 5. Password Incorrect Warning Password Edit Menu Figure 7. The warning message is displayed when the wrong OLD Password is entered Function Name PASSWORD EDIT OLD: _ _ _ _ NEW: _ _ _ _ CONFIRM: _ _ _ _ Explanation Edit the password (Default is 0000) Type the old password in 4 numbers, if the wrong password is entered, then refer to Figure 7 Type the new password in 4 numbers Re-type the new password for confirmation 17 TV Rating Menu Set the TV Ratings to block selected TV channels. MOVIE Rating Menu Set the Movie Ratings to block selected Movie channels. Function Name TV RATING TV Y: TV Y7: TV G: TV PG: TV 14: TV MA: FV: D: L: S: V: G: PG: PG 13: R: NC 17: X: Explanation <<< AGE >>> All Children Directed to Older Children General Audience Parental Guidance Suggested Parents Strongly Cautioned Mature Audience Only <<< CONTENT >>> Fantasy Violence Suggestive Dialogue Stronger Language Sexual Situation Violence General audience Parental Guidance suggested Parents strongly cautioned Restricted No one 17 and under admitted Adult audience only MOVIE RATING 18 Source Input: Component The component input video settings can be adjusted and saved separately from TV, Video and S-Video inputs. Main Picture Menu Function Name Brightness Contrast Sharpness Hue Saturation Aspect Ratio Explanation Brightness adjustment Contrast adjustment Adjust the Video Sharpness Adjust the Video Hue level Adjust the Video Saturation level Select TV display on "4:3" / "16:9" For the Main Input, Multi Screen, OSD, and Audio Menu operation, please refer to Pages 12-17. 19 Appendix This section lists the product specifications and common problems with corresponding solutions. Specifications Panel Type 20. 1" (full 20. 1" viewable diagonal area), TFT (Thin Film Transistor), Active Matrix VGA LCD, 640RGB*480 vertical stripe Surface treatment Anti-reflective coating + Anti-glare coating Viewing Angles Input Signal Video 160° (H) / 140° (V) TV system antenna / NSTC in US and TW Composite Video * 1 S­Video * 1 Audio Speaker Output Power Operating Conditions Voltage Temperature Humidity Altitude Storage Conditions Temperature Humidity Altitude Dimensions Physical Component Video * 1 ( YCbCr, YPbPr) RCA (L/R) Stereo * 2 5W * 2 100-240 VAC, 50/60 Hz (auto switch), 1. 5A 32° F to + 95° F (0° C to + 35° C) 20% to 90% (no condensation) To 3, 000 Meter -4° F to + 140° F (-20° C to + 60° C) 5% to 90% (no condensation) To 12, 000 Meter 573 mm (W) x 472 mm (H) x 227. 5 mm (D) 22. 76" (W) x 18. 58" (H) x 8. 96" (D) Weight Regulations Power Saving Modes On Active Off Net 19. 8 lb (9. 0 kg) FCC-B, UL, c-UL, <73W (Blue LED) <5W (LED OFF) 20 Troubleshooting No power · Make sure DC power button is ON (Green LED) · Make sure AC power cord is securely connected to the AC socket · Plug another electrical device (like a radio) to the power outlet to verify that the outlet is supplying the proper voltage Power is ON but no screen image · Adjust brightness and contrast · Check Source settings Wrong or abnormal colors · If any colors (red, green, or blue) are missing, check the video cable to make sure it is securely connected. [. . . ]