User manual WESTINGHOUSE MT80 THIN INSTALL GUIDE

[. . . ] 4 Installation to Double Wood Stud Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Installation to Solid Concrete or Cinder Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Installing Flat Panel Screen to Wall Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Adding Safety to Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Be sure to mount in a solid part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity. · Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor. · Make sure that the wall will safely support four times the combined load of the equipment and all attached hardware and components. 1 Use wall plate (AA), making sure that it is level, as a template to mark holes. holes to a minimum depth of 2-1/2" (64 mm). Insert anchors (EE) in holes flush with wall as shown (right). Place wall plate over anchors and secure with #14 x 2. 5" screws (CC). Tighten all fasteners. 1 concrete surface EE Drill holes and insert anchors (EE). WARNING · Tighten screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage screws, greatly reducing their holding power. · Never tighten in excess of 80 in. · lb (9 N. M. ). 2 AA CC EE Place plate (AA) over anchors (EE) and secure with screws (CC). 3 WARNING · Always attach concrete expansion anchors directly to load-bearing concrete. · Never attach concrete expansion anchors to concrete covered with plaster, drywall, or other finishing material. If mounting to concrete surfaces covered with a finishing surface is unavoidable, the finishing surface must be counterbored as shown below. If plaster/drywall is thicker than 5/8", custom fasteners must be supplied by installer. Tighten all fasteners. so lid co nc ret e AA CC EE cin de rb loc k INCORRECT CUTAWAY VIEW wall plate concrete wall plate CORRECT concrete plaster/ dry wall plaster/ dry wall 6 of 8 Visit the Westinghouse Web Site at www. westinghousedigital. com ISSUED: 03-02-05 SHEET #: 201-9323-1 For customer service call 1-866-287-5555. Note: Before starting this step refer to accompanying instruction sheet to install adapter brackets to flat panel screen. Installing Flat Panel Screen to Wall Plate 2 Insert two M5 x 25 mm socket head cap screws (DD) into mounting brackets (BB) and tighten a few turns to hold in place as shown in detail 1. Hang screen by the mounting brackets (BB) on wall plate (AA) as shown below. Make sure screen is safely hooked on mount before letting go. Screen can be adjusted horizontally if desired. WARNING · Always use an assistant or mechanical lifting equipment to safely lift and position the plasma television. BB BB AA detail 1 Adding Safety to Mount 3 Secure mounting brackets to wall plate (AA) with socket head cap screws as shown below and in detail 1. Tighten screws with 4 mm security allen wrench (FF). BB DD AA DETAIL 1 7 of 8 Visit the Westinghouse Web Site at www. westinghousedigital. com ISSUED: 03-02-05 SHEET #: 201-9323-1 For customer service call 1-866-287-5555. Limited Five-Year Warranty Westinghouse Digital Electronics warrants to original end-users of this Westinghouse television mounting product (the "Product") that the Product will be free from defects in material and workmanship, under normal use, for a period of five (5) years from the date of purchase by the original end-user, subject to the following terms and conditions: REPAIR OR REPLACEMENT ­ For a period of five (5) years from the original date of purchase, Westinghouse Digital Electronics will repair any defect in material or workmanship in the Product, or, at its option, replace a defective Product. Replacement parts and products will be warranted for either the remainder of the original warranty period or ninety (90) days from the date of delivery to the end-user, whichever occurs last. OBTAINING WARRANTY SERVICE ­ To obtain warranty services, you must either personally deliver or ship the Product to Westinghouse Digital Electronics, freight prepaid. [. . . ] If screws (G) are not long enough then use screws (F). 3 of 4 Visit the Westinghouse Web Site at www. westinghousedigital. com ISSUED: 01-18-05 SHEET #: 201-9325-1 For customer service call 1-866-287-5555. Installing Adapter Brackets 2 To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the screen. If screen has knobs on the back, remove them to allow the adapter brackets to be attached. Place adapter brackets (BB) on back of screen, align to holes, and center on back of screen as shown in figure 2. 1. Refer to step 1 to determine the proper fasteners to use. [. . . ]