User manual WHIRLPOOL 63851341

[. . . ] Always remain vigilant when cooking foods rich in fat and oil. - Never leave the appliance unattended during food drying. If alcoholic beverages are used when cooking foods (e. g. rum, cognac, wine), remember that alcohol evaporates at high temperatures. [. . . ] metallic mesh) - Two cookers for the same pot · In case of prolonged use, additional ventilation maybe needed (opening a window or increasing the extraction force of the hood). · This appliance is not intended for use by people (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge unless they have been given initial supervision or instruction concerning use of the appliance by a person responsible fortheir safety. · Keep children away from the hob when it is in use and do not let them play with the controls or any other appliance parts. SAVE THESE INSTRUCTIONS 5019 619 01340 ELECTRICAL CONNECTION Installation must be carried out by a qualified electrician who is fully aware of current safety and installation regulations. The manufacturer declines all liability for injury to persons or animals and for damage to property resulting from failure to observe the regulations provided in this chapter. GAS CONNECTION · The gas supply system must comply with local regulations. · You can find specific local regulations for some countries in the paragraph "Reference to Local Regulations". If no information concerning your country is given, please ask details to your installer. · The connection of the hob to the gas pipe network or gas cylinder must be made by means of a rigid copper or steel pipe with fittings complying with local regulations, or by means of a continuous-surface stainless steel hose complyingwith local regulations. The maximum length of the hose is 2 linear metres. · Before connecting the tube to the elbow fitting (A), interpose the washer (B) supplied, in compliance with EN 549. NOTE: if a stainless steel hose is used, it must be installed so as not to touch any mobile part of the furniture. It must pass through an area where there are no obstructions and where it is possible to inspect it on all its length. Position the clips (A) in the spaces provided on the hob trim (fig. Measure the centre point of the vertical sides of the cut-out (fig. Fit the brackets (C) in the centre of the vertical sides, aligning the upper edge of th e brackets so that they are flush with the worktop surface (fig. Fix the brackets with the 4 screws supplied (B) using the holes provided. Insert the hob in the cutout, making sure the clips (A) are secured in the spaces provided (fig. 4). C If the hob already has a power cable, follow the instructions given on the label attached to the cable. Connect the appliance to the electricity supply by means of an all-pole disconnect switch with minimum contact gap of 3 mm. B A fig. 5 For the distance between the underside of the induction hob and the kitchen unit (or separating panel), observe the dimensions given in the figure at the side. If a column unit is installed adjacent to the hob, leave a distance of at least 100 mm from the edge of the hob. UNDERCOUNTER OVEN INSTALLATION: · If an oven (which must be of our manufacture) is to be installed under the hob, ensure it is equipped with a cooling system and observe the distances given in the figure to the side. · There must be nothing between the cooktop and the oven (cross rails, panels, brackets, etc. ). MAINTENANCE Care and maintenance Clean the hob after each use in order to avoid damaging the surface and to prevent the formation of baked-on deposits which are difficult to remove. Before cleaning, make sure the cooking zones are switched off and that the residual heat indicator ("H") is not displayed. 5 mm · Disconnect power before servicing · DO NOT clean the hob with a steam cleaner NOTE: Periodically check for dust under the appliance, near the cooling air inlet or the outlet openings. [. . . ] · Models equipped with electrical ignition plugs and safety device require thorough cleaning of the plug end in order to ensure correct operation. Check these items frequently, and if necessary, clean them with a damp cloth. Any baked-on food should be removed with a toothpick or needle. Note: to avoid damaging the electric ignition device, do not use it when the burners are not in their housing. REPLACING THE INJECTORS (see the injector table in the Product Description Sheet) · Remove grids (A). [. . . ]