User manual WHIRLPOOL 8206327

[. . . ] MICROWAVE HOOD COMBINATION INSTALLATION INSTRUCTIONS This product is suitable for use above electric or gas cooking products up to 36" (91. 4 cm) wide. These installation instructions cover different models. The appearance of your particular model may differ slightly from the illustration in these installation instructions. NOTES: Proper installation is the responsibility of the installer. Product failure due to improper installation is not covered under the warranty. Table of Contents MICROWAVE HOOD COMBINATION SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 INSTALLATION REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Find the wall stud centerline(s) marked in Step 2 of "Locate Wall Stud(s), " and mark at least 1, preferably 2 or more, hole(s) through the mounting plate, closest to the centerline(s). See figures 1, 2 and/or 3 in "Possible Wall Stud Configurations" in "Locate Wall Stud(s)" section. The blackened holes in the shaded areas are ideal hole locations. Set mounting plate aside. Installation for One Wall Stud at Two Corner Holes (Figure 3) 1. Drill 3/16" (5 mm) holes into the wall stud at the 2 corner holes marked in Step 3 of "Mark Rear Wall. " 2. If installing on a second wall stud, drill 3/16" (5 mm) hole(s) into the wall stud at the holes marked in Step 4 of "Mark Rear Wall. " Refer to Figure 3 in "Possible Wall Stud Configurations. " in "Locate Wall Stud(s)" section. Drill 3/4" (19 mm) holes through the wall at the other 2 corner holes. Installation for Wall Studs at All Four Corner Holes (Figure 4) 1. Drill 3/16" (5 mm) holes into the studs at the 4 corner holes marked in Step 3 of "Mark Rear Wall. " 7 Attach Mounting Plate to Wall NOTE: Secure the mounting plate to the wall at all 4 corner holes drilled into the wall studs and/or drywall using either 1/4-20 x 3" round-head bolts and toggle nuts or 1/4 x 2" lag screws. Refer to illustrations in "Possible Wall Stud Configurations" in "Locate Wall Stud(s)" section. One Wall Stud at Two Corner Holes (Figure 3) 1. With the support tabs of the mounting plate facing forward, insert 1/4-20 x 3" round-head bolts through the 2 corner holes that fit over the two 3/4" (19 mm) holes drilled in Step 2 of "Installation for One Wall Stud at Two Corner Holes" in the "Drill Holes in Rear Wall" section. Start toggle nuts on the bolts from the back of the mounting plate. Leave enough space for the toggle nut to go through the wall and to open. Position mounting plate on the wall, making sure that the top of the mounting plate is aligned with the front edge of the upper cabinet. Push the 2 bolts with toggle nuts through the drywall, and finger tighten the bolts to make sure toggle nuts have opened against drywall. Insert 2 lag screws into the remaining 2 corner holes. If installing on a second wall stud, insert lag screw(s) into the other hole(s) drilled in Step 2 of "Installation for One Wall Stud at Two Corner Holes" in the "Drill Holes in Rear Wall" section. Check alignment of mounting plate, making sure it is level. Securely tighten all lag screws and bolts. No Wall Studs at Corner Holes (Figures 1 & 2) NOTE: The mounting plate must also be secured to the wall on at least 1 wall stud as well as at all 4 corners. With the support tabs of the mounting plate facing forward, insert 1/4-20 x 3" round-head bolts through all 4 corner holes of mounting plate. Start toggle nuts on bolts from the back of the mounting plate. Leave enough space for the toggle nuts to go through the wall and open. B Wall Studs at All Four Corner Holes (Figure 4) A C 1. [. . . ] Rectangular to round transition piece: 3¹/" x 10" to 6" = 5 ft (8. 3 x 25. 4 cm to 15. 2 cm = 1. 5 m) B. Roof cap: 3¹/" x 10" = 24 ft (8. 3 x 25. 4 cm = 7. 3 m) C. 90° elbow: 3¹ " x 10" = 25 ft (8. 3 x 25. 4 cm = 7. 6 m) D. 90° elbow: 6" = 10 ft (15. 2 cm = 3 m) E. [. . . ]