User manual WHIRLPOOL 8206587

[. . . ] MICROWAVE HOOD COMBINATION INSTALLATION INSTRUCTIONS This product is suitable for use above electric or gas cooking products up to 36" (91. 4 cm) wide. These installation instructions cover different models. The appearance of your particular model may differ slightly from the illustration in these installation instructions. NOTES: Proper installation is the responsibility of the installer. Product failure due to improper installation is not covered under the warranty. Table of Contents MICROWAVE HOOD COMBINATION SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 INSTALLATION REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] See figures 1, 2 and/or 3 in "Possible Wall Stud Configurations" in "Locate Wall Stud(s)" section. The blackened holes in the shaded areas are ideal hole locations. Set mounting plate aside. Installation for No Wall Studs at Corner Holes (Figures 1 & 2) 1. Drill 3/4" (19 mm) holes through the wall at both bottom corner holes marked in Step 3 of "Mark Rear Wall. " 2. Drill 3/16" (5 mm) hole(s) into the wall stud(s) at the hole(s) marked in Step 4 of "Mark Rear Wall. " Refer to figures 1 and 2 in "Possible Wall Stud Configurations" in "Locate Wall Stud(s)" section. Installation for Wall Stud at One Corner Hole (Figure 3) 1. Drill a 3/16" (5 mm) hole into the wall stud at the corner hole marked in Step 3 of "Mark Rear Wall. " 2. If installing on a second wall stud, drill a 3/16" (5 mm) hole into the wall stud at the other hole marked in Step 4 of "Mark Rear Wall. " Refer to Figure 3 in "Possible Wall Stud Configurations" in "Locate Wall Stud(s)" section. Drill a 3/4" (19 mm) hole through the wall at the other corner hole. Installation for Wall Studs at Both Corner Holes (Figure 4) 1. Drill 3/16" (5 mm) holes into the studs at the corner holes marked in Step 3 of "Mark Rear Wall. " 7 Attach Mounting Plate to Wall NOTE: Secure the mounting plate to the wall at both bottom corner holes drilled into the wall studs and/or drywall using either 1/4-20 x 3" round-head bolts and toggle nuts or 1/4 x 2" lag screws. Refer to illustrations in "Possible Wall Stud Configurations" in "Locate Wall Stud(s)" section. Wall Stud at One Corner Hole (Figure 3) 1. With the support tabs of the mounting plate facing forward, insert a 1/4-20 x 3" round-head bolt through the corner hole that fits over the 3/4" (19 mm) hole drilled in Step 3 of "Installation for One Wall Stud at One Corner Hole" in the "Drill Holes in Rear Wall" section. Start a toggle nut on the bolt from the back of the mounting plate. Leave enough space for the toggle nut to go through the wall and to open. Position mounting plate on the wall, making sure that the top of the mounting plate is aligned with the front edge of the upper cabinet. Push the bolt with toggle nut through the drywall, and finger tighten the bolt to make sure toggle nut has opened against drywall. Insert a lag screw into the remaining bottom corner hole. If installing on a second wall stud, insert a lag screw into the other hole drilled in Step 2 of "Installation for One Wall Stud at One Corner Hole" in the "Drill Holes in Rear Wall" section. Check alignment of mounting plate, making sure it is level. Securely tighten the lag screw(s) and bolt. No Wall Studs at Corner Holes (Figures 1 & 2) NOTE: The mounting plate must be secured to the wall on at least 1 wall stud as well as at both bottom corners. With the support tabs of the mounting plate facing forward, insert 1/4-20 x 3" round-head bolts through both bottom corner holes of mounting plate. Start toggle nuts on bolts from the back of the mounting plate. Leave enough space for the toggle nuts to go through the wall and open. B A C Wall Studs at Both Corner Holes (Figure 4) 1. [. . . ] Rectangular to round transition piece: 3¹/" x 10" to 6" = 5 ft (8. 3 x 25. 4 cm to 15. 2 cm = 1. 5 m) B. Roof cap: 3¹/" x 10" = 24 ft (8. 3 x 25. 4 cm = 7. 3 m) C. 90° elbow: 3¹ " x 10" = 25 ft (8. 3 x 25. 4 cm = 7. 6 m) D. 90° elbow: 6" = 10 ft (15. 2 cm = 3 m) E. [. . . ]