User manual WHIRLPOOL ACM 277 PROGRAM CHART

[. . . ] section “Troubleshooting Guide”). When the temperature returns to within normal levels the hob is able to be switched on again. Make sure the cooking zones and the bottoms of pots are dry before use. Do not place metal objects such as kitchen utensils (knives, forks, spoons, …), lids or other similar items on the cooking zones as they can become very hot. [. . . ] • For electrical connection, use an H05 RR-F type cable as specified in the table “Power supply voltage”. If the hob already has a power cable, follow the instructions given on the label attached to the cable. Connect the appliance to the electricity supply by means of an all-pole disconnect switch with minimum contact gap of 3 mm. Connecting to the terminal board Connect the yellow/green earth wire to the terminal with the symbol . This wire must be longer than the other wires. Remove the terminal block cover (A), undoing the screw and inserting the cover in the terminal block hinge (B). 70 mm of sheath from the power supply cable. Insert the power supply cable into the cable clamp and connect the wires to the terminal board as indicated in the diagram next to the terminal board itself. Secure the power cable with the cable clamp. Close the cover (C) and screw it on the terminal block with the removed screw - point (1). Each time the cooktop is connected to the mains it carries out an automatic check which lasts several seconds. 400V 3N ~ 230V ~ 230-240V~FOR AU ONLY 230V~FOR UK ONLY 230V 230V 230V 230V 400V 2N ~ 230V 3~ ONLY FOR BELGIUM 400V 2N~ FOR NL ONLY 230V 230V A 230V 230V B C 12 230V 230V 230V 31902090GB. fm Page 13 Friday, July 1, 2011 9:53 AM Installation and fixing The installer is responsible for any damage or injury resulting from incorrect installation. To guarantee correct operation, the appliance must be installed on a perfectly flat surface. For cut-out dimensions, see the figure below. Dimensions in mm 580 510 +1 0 The worktop must be -20 50mm thick. All the cooking zones are switched off. If the hob has been in use, the residual heat indicator “H” remains lit until the cooking zones have cooled down. The hob automatically switches off if no function is selected within 10 seconds of switching on. 14 31902090GB. fm Page 15 Friday, July 1, 2011 9:53 AM Switching on and adjusting cooking zones Heat setting indicator Button Cooking zone positioning Button + Selected cooking zone indicator After switching on the hob and positioning the pot on the chosen cooking zone, adjust the heat setting using the button +. When switched on, the display shows level 5. Each cooking zone has different heat settings that can be adjusted using the buttons +/-, which go from “1”: min. Some cooking zones have a fast boil function (Booster), shown on the display with the letter “P”. Fast boil function (Booster) This function, only present on some cooking zones, makes it possible to exploit the hob's maximum power (for example to bring water to the boil very quickly). To select this function, press the button “+” until “P” appears on the display or, after switching the hob on, press the “-” button for the selected cooking zone. In this case too, “P” appears on the display. After 10 minutes' use of the booster function, the appliance automatically sets the zone to level 9. To deactivate the timer, press the button “-” until the display shows “0:0” or press the buttons “+” and “-” of the timer at the same time. Switching off cooking zones Select the cooking zone to be switched off by pressing the “+” or “-” key (a dot lights up at the bottom right hand side of the heat setting indicator). Press the key “-” to set the level to “0”. The cooking zone can also be switched off by pressing keys “+” and “-” at the same time. [. . . ] The minute minder function can only be used when the hob is switched off; if it is then switched on, the minute minder countdown is automatically cancelled. Child guard accessory AMH 122 Control panel warnings. Residual heat indicator. The hob is fitted with a residual heat indicator for each cooking zone. These indicators alert the user when cooking zones are still hot. This accessory can be obtained from the After-sales Service under Part N° 481931018436 Timer The timer can be used to set a max. cooking time of 99 minutes (1 hour and 39 minutes) for one cooking zone only. Select the cooking zone to be used with the timer (an illuminated dot appears to the bottom right hand side of the heat setting indicator on the display), then set the desired cooking time using the buttons “+” and -“-” of the timer function (see figure above). [. . . ]