User manual WHIRLPOOL ACM 710

[. . . ] 31902052GB. fm Page 11 Wednesday, September 3, 2008 4:05 PM IMPORTANT SAFETY INFORMATION This manual contains important information regarding safety, the use and maintenance of your new hob. Read the manual and keep it in an easily accessible place for future consultation. thermoprotector activates, automatically switching off the hob. The display shows an error message (see. [. . . ] If necessary, cut the kitchen unit and worktop to fit before installing the hob. Clean the cutout of any chips that could compromise appliance operation. 77x35 770 350 52 325 min. 8 490 +2 0 +2 0 275 380 510 330 +1 0 +2 0 750 Domino 380 51 484 342 min. 8 +2 0 +2 0 490 350 Dimensions in mm To guarantee correct operation, the appliance must be installed on a perfectly flat surface. If necessary, cut the kitchen unit and worktop to fit before installing the hob. Clean the cutout of any remaining dust that could compromise appliance operation. For the distance between the underside of the induction hob and the kitchen unit (or separating panel), observe the dimensions given in the figure at the side. If a column unit is installed adjacent to the hob, leave a distance of at least 100 mm from the edge of the hob. min. Position the clips (A) in the spaces provided on the hob trim (fig. Measure the centre point of the vertical sides of the cutout (fig. Fit the brackets (C) in the centre of the vertical sides, aligning the upper edge of the brackets so that they are flush with the worktop surface (fig. Fix the brackets with the 4 screws supplied (B) using the holes provided. Insert the hob in the cutout, making sure the clips (A) are secured in the spaces provided (fig. 2 13 31902052GB. fm Page 14 Wednesday, September 3, 2008 4:05 PM A fig. 4 Undercounter oven installation: · If an oven (which must be of our manufacture) is to be installed under the hob, ensure it is equipped with a cooling system and observe the distances given in the figure to the side. · There must be nothing between the cooktop and the oven (cross rails, panels, brackets, etc. ). 5 mm OPERATING INSTRUCTIONS Control panel Timer On/Off Child lock the symbols are not active!To select the desired functions, touch the areas below. Cooking zone controls and corresponding display Control panel graphics shown in these instructions might not match exactly the graphics of your hob. Button's functions are the same for all hob models. Switching the hob ON/OFF To switch the hob on, press the button for approx. 2 seconds until the cooking zone displays light up. To switch off, press the same button until the displays switch off. If the hob has been in use, the residual heat indicator "H" remains lit until the cooking zones have cooled down. The hob automatically switches off if no function is selected within 10 seconds of switching on. 14 31902052GB. fm Page 15 Wednesday, September 3, 2008 4:05 PM Switching on and adjusting cooking zones Heat setting indicator Button Cooking zone positioning Button + Selected cooking zone indicator After switching on the hob and positioning the pot on the chosen cooking zone, adjust the heat setting using the button +. [. . . ] · Clean the hob and dry it thoroughly. · If, when the hob is switched on, alphanumeric codes appear on the display, consult the following table for instructions. POSSIBLE CAUSES REMEDY Water or utensils on control panel Clean the control panel The internal temperature of electronic parts is too high The sensor detects a discrepancy between the appliance voltage and that of the mains supply Wait for the hob to cool down before using it again Disconnect the hob from the mains and check the electrical connection F42 or F43 F12, F21, F25, F36, F37, F40, F47, F56, F58, F60 Call the After-Sales Service and specify the error code WARNING!If you are unable to turn the glass-ceramic hob off after using it, disconnect it immediately from the power supply. After-sales Service Before contacting After-sales Service: · Try to solve the problem (see "Troubleshooting Guide"). [. . . ]