User manual WHIRLPOOL ACM 754/BA INSTRUCTION FOR USE

[. . . ] 31901498. book Page 12 Thursday, June 25, 2009 7:59 PM ENGLISH Installation Page 2 Instructions for use Page IMPORTANT SAFETY INSTRUCTIONS YOUR SAFETY AND THAT OF OTHERS IS PARAMOUNT This manual and the appliance itself provide important safety messages, to be read and observed at all times. This is the safety alert symbol, pertaining to safety, which alerts users to potential hazards to themselves and others. All safety warnings are preceded by the danger symbol and the following terms: DANGER WARNING Indicates a hazardous situation which, if not avoided, will cause serious injury. Indicates a hazardous situation which, if not avoided, could cause serious injury. All safety warnings give specific details of the potential risk present and indicate how to reduce risk of injury, damage and electric shock resulting from improper use of the appliance. [. . . ] 70 mm of sheath from the power supply cable. Insert the power supply cable into the cable clamp and connect the wires to the terminal board as indicated in the diagram next to the terminal board itself. Secure the power cable with the cable clamp. Close the cover (C) and screw it on the terminal block with the removed screw - point (1). Each time the cooktop is connected to the mains it carries out an automatic check which lasts several seconds. If the hob already has a power cable, follow the instructions given on the label attached to the cable. Connect the appliance to the electricity supply by means of an allpole disconnect switch with minimum contact gap of 3 mm. GB14 230 V 230 V 230 V 230 V 230 V 4 X 1. 5 mm2 31901498. book Page 15 Thursday, June 25, 2009 7:59 PM INSTRUCTIONS FOR USE Control Panel Description The control panel is equipped with touch controls: to use them, just press the corresponding symbol (a light touch is sufficient). To select and activate the cooking zones To set the minute counter Hob ON/OFF To select one of the automatic functions Slide touchscreen To enable the hold function To lock the control panel To select the flexible zone function First use / after a power failure After connecting the hob to the electrical power supply, the control panel is locked (the indicator light above the key is ON). To unlock the control panel, press and hold the key for 3 seconds. The indicator light switches off and the hob can be used normally. Switching the hob ON/OFF To switch the hob on, press and hold the key for approx. 2 seconds: the indicator light above the key turns on and hyphens appear inside the circles which represent the cooking zones. To switch off, press the same key until the hob switches off. All the cooking zones are switched off. i The hob automatically switches off if no function is selected within 10 seconds of switching on. Switching on and adjusting cooking zones Indicates that one of the automatic functions is On Cooking zone timer Cooking zone selection and selected cooking zone/power level display Slide touchscreen (power adjustment) After switching on the hob, position the pot on the chosen cooking zone. Activate the cooking zone by pressing the relative round key: the round key displays number 5 which corresponds to the intermediate power level. The hob automatically switches off if no function is selected within 10 seconds of switching on. If you are using a pot that is not suitable, not correctly positioned or not of the correct dimensions for your induction hob, the message “no pot” will appear in the display (see figure on the left). If no pot is detected within 60 seconds, the hob switches off. To change the power level, move your finger horizontally on the slide touchscreen: the number inside the circle will change with just a quick slide of the finger from a minimum of 1 to a maximum of 9. You can activate the booster function by pressing “BOOST” on the slide touchscreen (“P” on the display). If more than one cooking zone is on, the slide touchscreen allows you to change the power level of the selected zone, indicated by the presence of a luminous dot at the bottom right of the power level indicator. Press the key: blinks on the display in place of the power levels. To resume cooking, press the key again. Flexible Zone This function can be used to combine two zones and manage them as one single cooking zone. [. . . ] C81, C82, C83 F42 or F43 The control panel switches off because The internal temperature of electronic of excessively high temperatures. The connection voltage is wrong. The sensor detects a discrepancy Disconnect the hob from the mains between the appliance voltage and that and check the electrical connection. of the mains supply. F12, F21, F25, F36, F37, F40, F47, F56, F58, Call the After-sales Service and specify the error code. F60, F61, F62, F63, F64 AFTER-SALES SERVICE Before contacting After-sales Service 1. See if you can eliminate the problem on your own by referring to the “Troubleshooting guide”. [. . . ]