User manual WHIRLPOOL ACM 759/NE INSTRUCTION FOR USE

[. . . ] 31902074. book Page 13 Thursday, December 9, 2010 10:42 AM ENGLISH Installation Page 2 Instructions for use Page IMPORTANT SAFETY INSTRUCTIONS YOUR SAFETY AND THAT OF OTHERS IS PARAMOUNT This manual and the appliance itself provide important safety warnings, to be read and observed at all times. This is the safety alert symbol, pertaining to safety, which alerts users to potential hazards to themselves and others. All safety messages are preceded by the safety alert symbol and the following terms: Indicates a hazardous situation which, if not avoided, will result in serious injury. DANGER WARNING Indicates a hazardous situation which, if not avoided, could result in serious injury. All safety warnings give specific details of the potential risk present and indicate how to reduce risk of injury, damage and electric shock resulting from improper use of the appliance. Please observe the following instructions: - The appliance must be disconnected from the power supply before carrying out any installation work. [. . . ] If the hob already has a power cable, follow the instructions given on the label attached to the cable. Connect the appliance to the electricity supply by means of an all-pole disconnect switch with minimum contact gap of 3 mm. GB15 230 V 4 X 1. 5 mm2 31902074. book Page 16 Thursday, December 9, 2010 10:42 AM INSTRUCTIONS FOR USE Control Panel Description The control panel is equipped with touch controls: to use them, just press the corresponding symbol (a light touch is sufficient). To select and activate the cooking zones To set the minute counter Hob ON/OFF To enable the hold function To lock the control panel To select the flexible zone function To select one of the automatic functions Slide touchscreen First use / after a power failure After connecting the hob to the electrical power supply, the control panel is locked (the indicator light above the key is ON). To unlock the control panel, press and hold the key for 3 seconds. The indicator light switches off and the hob can be used normally. Switching the hob ON/OFF To switch the hob on, press and hold the key for approx. 2 seconds: the indicator light above the key turns on and hyphens appear inside the circles which represent the cooking zones. To switch off, press the same key until the hob switches off. All the cooking zones are switched off. i The hob automatically switches off if no function is selected within 10 seconds of switching on. Switching on and adjusting cooking zones Indicates that one of the automatic functions is On Cooking zone timer Cooking zone selection and selected cooking zone/power level display Slide touchscreen (power adjustment) After switching on the hob, position the pot on the chosen cooking zone. Activate the cooking zone by pressing the relative round key: the round key displays number 5 which corresponds to the intermediate power level. To change the power level, move your finger horizontally on the slide touchscreen: the number inside the circle will change with just a quick slide of the finger from a minimum of 1 to a maximum of 9. You can activate the booster function by pressing “BOOST” on the slide touchscreen (“P” on the display). The “BOOST” power function can be used for a maximum of 10 minutes, after which the appliance automatically sets the power level at level 9. In models with three cooking zones, three “BOOST” levels can be selected at the same time: in this case the appliance automatically adapts the power distribution between the three zones. If more than one cooking zone is on, the slide touchscreen allows you to change the power level of the selected zone, indicated by the presence of a luminous dot at the bottom right of the power level indicator. To select a zone, simply press the relative round key. If you are using a pot that is not suitable, not correctly positioned or not of the correct dimensions for your induction hob, the message “no pot” will appear in the display (see figure on the left). If no pot is detected within 60 seconds, the hob switches off. Switching off cooking zones Select the cooking zone to be switched off by pressing the relative round key (a dot lights up at the bottom right of the power level indicator). The cooking zone switches off and, if the zone is still hot, the letter “H” appears in the circle. It is ideal for using large oval, rectangular and elongated pots or pans, (with bottom measuring max. After switching the hob on, press the key : the displays of the two cooking zones show the level “5”; both luminous dots to the side of the number are lit, indicating a single cooking selected. To change the power level, use the slide touchscreen: the number inside the circle will change with just a quick slide of the finger from a minimum of 1 to a maximum of 9. To deactivate the flexible zone function, press the key : the cooking zones revert to operating singly again. [. . . ] Wait for the hob to cool down before using it again. The control panel switches off because of The internal temperature of electronic excessively high temperatures. The connection voltage is wrong. The sensor detects a discrepancy between Disconnect the hob from the mains the appliance voltage and that of the and check the electrical connection. mains supply. F12, F21, F25, F36, F37, F40, F47, F56, F58, F60, F61, F62, F63, F64 Call the After-sales Service and specify the error code. GB18 31902074. book Page 19 Thursday, December 9, 2010 10:42 AM AFTER-SALES SERVICE Before contacting After-sales Service 1. See if you can solve the problem yourself with the help of the suggestions given in the “Troubleshooting guide”. [. . . ]