User manual WHIRLPOOL ACM711BF

[. . . ] 210 mm 145 mm 210 mm 145 mm 210 mm 180 mm 145 mm 180 mm 180 mm 240 mm 145 mm 210 mm 210 mm 240 mm 145 mm 210 mm 180 mm 260 mm 145 mm 145 mm 210 mm 280/180 mm 145 mm 145 mm 1 ENGLISH DEUTSCH FRANÇAIS NEDERLANDS ESPAÑOL PORTUGUÊS ITALIANO ΕΛΛΗΝΙΚΑ SVENSKA NORSK DANSK SUOMI POLSKI ČESKY SLOVENSKY MAGYAR РУССКИЙ БЪЛГАРСКИ ROMÂNĂ УКРАЇНСЬКА Installation Installation Installation Installatie Instalación Instalação Installazione Εγκατάσταση Installation Installasjon Installation Asennus Instalacja Instalace Inštalácia Üzembe helyezés Установка Инсталиране Instalarea Установлення Page 2 Seite 2 Page 2 Pagina 2 Página 2 Página 2 Pagina 2 Σελίδα 2 Sidan 2 Side 2 Side 2 Sivu 2 Strona 2 Strana 2 Strana 2 Oldal 2 Страница 2 Страница 2 Pagina 2 Сторінка 2 Instructions for use Bedienungsanleitung Mode d’emploi Gebruiksaanwijzing Instrucciones de uso Instruções de utilização Istruzioni per l’uso Οδηγίες χρήσης Bruksanvisning Bruksanvisning Brugervejledning Käyttöohje Instrukcja obsługi Návod k použití Návod na používanie Használati útmutató Page Seite Page Pagina Página Página Pagina Σελίδα Sidan Side Side Sivu Strona Strana Strana Oldal 4 12 20 28 36 44 52 60 68 76 84 92 101 110 118 126 134 144 153 161 Инструкции по пользованию прибором Страница Инструкции за употреба Страница Instrucţiuni de utilizare Інструкції з експлуатації Pagina Сторінка 2 A 54 mm 560 +2 mm 0 R = Min. 50 mm 580 mm 510 mm 0 490 +2 mm mm 553 mm 30 483 mm +1 0 583 +2 mm 0 560+2 0 R = 11, 5 mm 490+2 mm 0 513 +2 mm 0 mm R = 11, 5 mm 6 mm R = Min. 8 mm B 770 mm 54 mm 0 490 +2 750 +2 mm 0 R = Min. 50 mm 510 mm 30 mm mm +1 0 773 +2 mm Min. [. . . ] For built-in dimensions and installation instruction, see the pictures in page 2. PREPARING THE CABINET FOR FITTING WARNING • • • • • • Install a separator panel under the hob. The lower part of the product must not be accessible after installation. Do not fit the separator panel if an undertop oven is installed. min. 20 mm 6-7 cm The distance between the underside of the appliance and the separator panel must respect the dimensions given in the figure. In order to ensure the correct operation of the product, do not obstruct the minimum required clearance between the hob and the top of the unit (min. If an undertop oven is installed, make sure the oven is equipped with a cooling system. Do not install the hob above a dishwasher or washing-machine, so that the electronic circuits do not come into contact with steam or moisture which could damage them. In the case of flush-mounted installation, call the After-Sales Service to request assembly of screws kit 4801 211 00112. To remove the hob, use a screwdriver (not provided) to prise off the perimeter clips on the underside of the appliance. EN6 ELECTRICAL CONNECTION Disconnect the appliance from the power supply. Installation must be carried out by qualified personnel who know the current safety and installation regulations. The manufacturer declines all liability for injury to persons or animals and for damage to property resulting from failure to observe the regulations provided in this chapter. The power cable must be long enough to allow the hob to be removed from the worktop. Make sure the voltage specified on the dataplate located on the bottom of the appliance is the same as that of the home. WARNING - - Connection to the terminal block For the electrical connection of the power cord is present in the supply. Connect the ground cable yellow / green to terminal symbol . Remove the terminal cover (A) by unscrewing the screw and insert the cover into the hinge (B) of the terminal. Plug the power cord into the clamp and connect the wires to the terminal block as shown in the wiring diagram located near the terminal. Secure the power cable with the cable clamp. To activate the control panel lock, switch the hob on and press the Lock function button for three seconds; an acoustic signal and a luminous indicator near the padlock symbol signal activation. The control panel is locked except for the switching off function. To deactivate the control lock, repeat the activation procedure. The luminous dot goes off and the hob is active again. The presence of water, liquid spilled from pots or any objects resting on the button below the symbol can accidentally activate or deactivate the control panel lock. Timer The timer can be used to set the cooking time for a maximum of 99 minutes (1 hour and 39 minutes) for all the cooking zones. [. . . ] If, when the hob is switched on, alphanumeric codes appear on the display, consult the following table for instructions. If the hob cannot be switched off after using it, disconnect it from the power supply. ERROR CODE DESCRIPTION POSSIBLE CAUSES ERROR ELIMINATION C81, C82 C83 C85 F02 or F04 or C84 F01, F05, F06, F07, F10, F12, F25, F33, F34, F36, F37, F46, F47, F48, F49, F58, F61, F62, F63, F72, F74, F77 The control panel switches off The internal temperature of electronic Wait for the hob to cool down because of excessively high parts is too high before using it again. temperatures The control panel indicates the error Cooktop has been supplied with over Cooktop may be still used but call code hob off because of an issue on voltage the After-Sales Service electronic circuit Hob is not able to give power to Pot is not suitable to the induction hob Use another induction pot the pot The sensor detects a discrepancy Disconnect the hob from the The connection voltage is wrong or between the appliance voltage and mains and check the electrical issue to the power supply that of the mains supply connection Disconnect the hob from the power supply.  Wait a few seconds and plug it again. [. . . ]