User manual WHIRLPOOL ACM800NE

[. . . ] IMPORTANT SAFETY INSTRUCTIONS YOUR SAFETY AND THAT OF OTHERS IS VERY IMPORTANT This manual and the appliance itself provide important safety messages, to be read and always observed. This is the danger symbol, regarding safety, warning of potential risks to users and others. All safety messages will be preceded by the danger symbol and the following words: DANGER WARNING Indicates a hazardous situation which, if not avoided, will result in serious injury. Indicates a hazardous situation which, if not avoided, could cause serious injury. All messages relevant to safety specify the potential risk to which they refer and indicate how to reduce the risk of injury, damage and electric shocks due to incorrect use of the appliance. [. . . ] 5 mm • • • • • • The distance between the underside of the appliance and the separator panel must respect the dimensions given in the figure. In order to ensure the correct operation of the product, do not obstruct the minimum required clearance between the hob and the top of the unit (min. If an undertop oven is installed, make sure the oven is equipped with a cooling system. Do not install the hob above a dishwasher or washing-machine, so that the electronic circuits do not come into contact with steam or moisture which could damage them. In the case of flush-mounted installation, call the After-Sales Service to request assembly of screws kit 4801 211 00112. To remove the hob, use a screwdriver (not provided) to prise off the perimeter clips on the underside of the appliance. ELECTRICAL CONNECTION Disconnect the appliance from the power supply. Installation must be carried out by qualified personnel who know the current safety and installation regulations. The manufacturer declines all liability for injury to persons or animals and for damage to property resulting from failure to observe the regulations provided in this chapter. The power cable must be long enough to allow the hob to be removed from the worktop. Make sure the voltage specified on the dataplate located on the bottom of the appliance is the same as that of the home. WARNING - - Connection to the terminal block For the electrical connection, use an H05RR-F cable as specified in the table below. Wires 230 V ~ + 230-240 V ~ + 230 V 3 ~ + 400 V 3N ~ + 400 V 2N ~ + Number x size 3 x 4 mm 2 400 V 3N ~ 230 V ~ 230-240 V ~ (Australia only) 230 V ~ (UK only) 3 X 4 mm2 (Australia only) 4 x 1. 5 mm2 230 V 230 V 230 V 230 V 5 x 1. 5 mm2 4 x 1. 5 mm2 A B C 400 V 2N ~ 230 V 3 ~ (Belgium only) 400 V 2N ~ (Holland only) 230 V 230 V Important: - Based on the wiring diagram (see figure) either keep or remove the metal jumpers between the screws on the terminal block L1-L2 and N1-N2. - If the cable is provided, see the connection instructions attached to the cable. - Make sure all six screws on the terminal block are tightened after connecting the cables. Example of jumper present (left) or removed (right). See the wiring diagram for details (the jumpers can be between L1-L2 and between N1-N2). GB14 230 V 230 V 230 V 230 V 230 V Connect the yellow/green earth wire to the terminal with the symbol . This wire must be longer than the other wires. Remove the terminal block cover (A), undoing the screw and inserting the cover in the terminal block hinge (B). Insert the power cable in the cable clamp and connect the wires to the terminal block as indicated in the connection diagram located near it. Secure the power cable with the cable clamp. Close the cover (C) and screw it on the terminal block with the previously removed screw. Each time the power is connected, the hob performs an automatic check for a few seconds. If the hob already has a power cable, follow the instructions attached to the cable. [. . . ] • Sugar or foods with a high sugar content damage the hob and must be immediately removed. • Salt, sugar and sand could scratch the glass surface. • Use a soft cloth, absorbent kitchen paper or a specific hob cleaner (follow the Manufacturer’s instructions). TROUBLESHOOTING GUIDE • • • • • Read and follow the instructions given in the section “Instructions for use”. Check that the electricity supply has not been shut off. [. . . ]