User manual WHIRLPOOL ACM866BF

[. . . ] 210 mm 145 mm 210 mm 280/180 mm 210 mm 180 mm 145 mm 210 mm 210 mm 145 mm 280/180 mm 145 mm 210 mm 145 mm 145 mm DEUTSCH ENGLISH FRANÇAIS NEDERLANDS ESPAÑOL PORTUGUÊS ITALIANO ΕΛΛΗΝΙΚΑ SVENSKA NORSK DANSK SUOMI POLSKI ČESKY SLOVENSKY MAGYAR РУССКИЙ БЪЛГАРСКИ ROMÂNĂ УКРАЇНЕЦЬ Installation Installation Installation Installatie Instalación Instalação Installazione Εγκατάσταση Montering Installasjon Installation Asennus Instalacja Instalace Inštalácia Üzembe helyezés Установка Инсталиране Instalarea Установлення Seite 8 Page 17 Page 27 Pagina 35 Página 44 Página 53 Pagina 62 Σελίδα 72 Sidan 81 Side 90 Side 99 Sivu 108 Strona 118 Strana 126 Strana 135 Oldal 144 Страница 164 Pagina 174 Сторінка 183 Bedienungsanleitung Instructions for use Mode d’emploi Gebruiksaanwijzing Instrucciones de uso Instruções de utilização Istruzioni per l’uso Οδηγίες χρήσης Bruksanvisning Bruksanvisning Brugervejledning Käyttöohje Instrukcja obsługi Návod k použití Návod na používanie Használati útmutató Инструкции за употреба Instrucţiuni de utilizare Інструкції з використання Seite Page Page Pagina Página Página Pagina Σελίδα Sidan Side Side Sivu Strona Strana Strana Oldal Страница Страница Pagina Сторінка 10 18 28 37 46 55 64 73 83 91 101 110 119 128 137 146 155 165 175 184 Страница 154 Инструкции по пользованию прибором 3 A 52 mm 560 +2 mm 0 R = Min. 50 mm 580 650 700 mm 510 mm 490 +2 mm 0 mm 553 mm 30 483 mm +1 0 583 +2 mm 0 560+2 0 R = 11, 5 mm 490+2 mm 0 513 +2 mm 0 mm R = 11, 5 mm 6 mm R = Min. 8 mm B 770 mm 52 mm 0 490 +2 750 +2 mm 0 R = Min. 50 mm 510 mm 30 mm mm +1 0 773 +2 mm Min. [. . . ] Wires 220-240 V ~ + 220-240 V 3 ~ + 380-415 V 3N ~ + 380-415 V 2N ~ + Number x size 3 x 4 mm2 4 x 1. 5 mm2 5 x 1. 5 mm2 230 V 230 V 230 V 230 V 380-415 V 3N ~ 220-240 V ~ 220-240 V ~ (AU and UK) 4 x 1. 5 mm2 A B C 380-415 V 2N ~ 220-240 V 3 ~ (Belgium only) 380-415 V 2N ~ (Holland only) 230 V 230 V Important: - Based on the wiring diagram (see figure) either keep or remove the metal jumpers between the screws on the terminal block L1-L2 and N1-N2. - If the cable is provided, see the connection instructions attached to the cable. - Make sure all six screws on the terminal block are tightened after connecting the cables. Example of jumper present (left) or removed (right). See the wiring diagram for details (the jumpers can be between L1-L2 and between N1-N2). Connect the yellow/green earth wire to the terminal with the symbol . This wire must be longer than the other wires. Remove the terminal block cover (A), undoing the screw and inserting the cover in the terminal block hinge (B). Insert the power cable in the cable clamp and connect the wires to the terminal block as indicated in the connection diagram located near it. Secure the power cable with the cable clamp. Close the cover (C) and screw it on the terminal block with the previously removed screw. Each time the power is connected, the hob performs an automatic check for a few seconds. If the hob already has a power cable, follow the instructions attached to the cable. Connect the appliance to the power supply by means of a multipole switch with minimum contact gap of 3mm. INSTRUCTIONS FOR USE Control Panel Description Control panel Power management step 1 On/Off Timer Control panel lock/Special function/ Power management step 2 and 4 Power management step 1 Cooking zone controls and corresponding display EN18 230 V 230 V 230 V 230 V 230 V Power management step 1 On/Off Timer Control panel lock/Special function/ Power management step 2 and 4 Power management step 1 Cooking zone controls and corresponding display Switching the hob ON/OFF To switch the hob on, press the button for approx. 2 seconds until the cooking zone displays light up. To switch off, press the same button until the displays switch off. When the set time has elapsed, an acoustic signal sounds and the cooking zone switches off automatically. To deactivate the timer, keep the Timer button pressed for at least 3 seconds. To set the timer for another zone, repeat the above steps. The timer display always shows the timer for the selected zone or the shortest timer. To modify or deactivate the timer, press the cooking zone selection button for the timer in question. Control panel warnings. Special functions (If available) Some models have special functions: Automatic function The function automatically sets a power level suitable for maintaining a low boil. Activate this function after bringing to the boil, pressing the corresponding zone button first and then the button . EN19 Simmering After bringing to the boil, press the key and the hob will automatically set the correct power level to keep the pot simmering. “A” appears on the display: the indicator light lights up. [. . . ] If the hob cannot be switched off after using it, disconnect it from the power supply. ERROR CODE DESCRIPTION POSSIBLE CAUSES ERROR ELIMINATION C81, C82 The control panel switches off because of excessively high temperatures The connection voltage is wrong The internal temperature of electronic parts is too high The sensor detects a discrepancy between the appliance voltage and that of the mains supply Wait for the hob to cool down before using it again. Disconnect the hob from the mains and check the electrical connection F42 or F43 F12, F21, F25, F36, F37, F40, F47, F56, F58, F60 Call the After-Sales Service and specify the error code NOISES MADE BY THE HOB Induction hobs can make whistling or crackling sounds during normal operation, these actually come from the pots and pans as a result of the characteristics of the bottoms (for example, bottoms made of several layers of material, or uneven bottoms). These noises vary depending on the pots and pans used and the amount of food they contain, and are not indicative of a defect of any kind. In addition, the induction hob is equipped with an internal cooling system to control the temperature of electronic parts; as a result, during operation and for several minutes after the hob has been switched off, the noise of the cooling fan will be audible. [. . . ]