User manual WHIRLPOOL ACO 020 INSTRUCTION FOR USE

[. . . ] If this booklet is not present you can ask your supplier for it, specifying: 17 • • 1. 5 The serial number (stamped on the relevant plaque, see paragraph 4. PREARRANGEMENTS OF CUSTOMER'S RESPONSIBILITY It is the Customer's responsibility to carry out everything specified in the documentation. Unless different prior arrangements have been made, the following are usually the Customer's responsibility: • Predisposition of the area, including any building work and or canalisation required; • Electric power supply in accordance with the power regulations in the country of use; • Cleaning materials. [. . . ] 4 DANGER ZONE There are no danger zones during use because the upright and/or table refrigerator has all the necessary safety devices. If repairs or maintenance have to be carried out requiring the removal of the safety devices, it is necessary first to make sure that all power sources have been switched off. For this reason in the upright and/or table refrigerator it is necessary to deactivate: - The electric plant, putting the main switch off and pulling out the plug. At the end of any work, it is absolutely imperative that all safety devices are re-activated. 5 SWITCHING OFF THE APPLIANCE For switch off the fridge or table , is necessary to proceed as fallow: • Turn the main switch on off position • Remove power cable 21 4. 6 PLAQUES PLAQUE A Plaque regarding the characteristics of the appliance Example CE – PCT Example NSF - UL Plaque regarding the Electrical apparatus PLAQUE B Remove the tension before removing the protection Plaque regarding the Electrical apparatus PLAQUE C Earth symbol Plaque regarding the Electrical apparatus PLAQUE D Warning!The manufacturer and the retailer decline all responsibility if the power line is not protected by a high sensitivity magnetothermic switch (IN - 16 A ID - 30 mA) PLAQUE E max. 1 TRANSPORT AND MOVEMENT The transport and movement of the upright and/or table refrigerators must take place in the upright position, respecting any indications shown on the packaging. Transport must be carried out by qualified staff. The upright and/or table refrigerators must be transported in such a way as to avoid any damage. The appliance is prepared for transport with or without packaging depending on the means of transport and the route. if packaged , it is in cardboard or wood , adequately protected. Movement must be carried out using a lift truck or trans-pallets with suitable forks (length at least 2/3 of the dimensions of the object) Damage to the appliance caused during transport and movement is not covered by the GUARANTEE. Repairs or substitution of damaged parts is at the Customer's expense. 2 STORAGE In the case of long periods of inactivity, the upright and/or table refrigerators must be stored with attention to the relevant storage place and time: • Store the upright and/or table refrigerator in an enclosed area; • Protect upright and/or table refrigerator from bumps or stress; • Protect upright and/or table refrigerator from high thermal variation; • Avoid upright and/or table refrigerator coming into contact with corrosive substances. 3 CHECKS Before putting upright and/or table refrigerator into operation, it is necessary to carry out a series of checks to prevent errors or accidents during the activating phase: • • • • 6. Check that there has not been any damage to the upright and/or table refrigerator during assembly. Check with care the integrity of the control panel, the electric cable and the tubes. Check the precise connection to external energy supply. Check the free movement and rotation of any moving parts. INSTALLATION For an optimum functioning of the unit it is advisable to place the refrigerator in a zone with a good ex change of air and far away from any sources of heat. 1 SET UP • Carefully remove the packaging from the refrigerator; • Remove the white PVC protection film from the stainless steel and all the protection used by the company to reduce the risk of damage during transport; • Place the refrigerator on a flat level surface (use the adjustable feet). [. . . ] TROUBLESHOOTING The following table shows the most frequent problems, possible causes and remedies. PROBLEM DESCRIPTION The appliance does not come on The refrigerator unit does not start POSSIBLE CAUSE The main switch is "off" There is no tension Other Set temperature is reached Defrosting is in operation Control Panel is broken Other Room is too hot Condenser is dirty Refrigerant fluid is insufficient Condenser fan has stopped Door not properly closed Evaporator is frosted up Defrost valve is open Control Panel is broken Temperature probe is broken Door is not airtight Improper use Control Panel is broken Blocked Appliance not levelled Appliance not levelled Contact with external bodies Screws or nuts loose Other SOLUTION Main switch “on” Check plug, socket, fuse, electric connection Contact technical assistance Set new temperature Wait for end of cycle, switch off and switch back on Contact technical assistance Contact technical assistance Air better Clean condenser Contact technical assistance Contact technical assistance Check door seals Manual defrosting Contact technical assistance Contact technical assistance Contact technical assistance Close door Contact technical assistance Contact technical assistance Clean drain and discharge Contact technical assistance Check that appliance is level. Check that no tube or ventilator fan is in contact with external bodies. Tighten Contact technical assistance The refrigerator is continuously working but does not reach the set temperature Refrigerator does not stop at set temperature Ice blocks on evaporator Pool of water or ice in drip tray Appliance is noisy IN ORDER TO GUARANTEE THE EFFICIENCY OF THE APPLIANCE AND ITS CORRECT FUNCTIONING THE MANUFACTURER'S INSTRUCTIONS MUST BE FOLLOWED AND PERIODIC SERVICING MUST BE CARRIED OUT BY PROFESSIONALLY QUALIFIED PERSONNEL. [. . . ]