User manual WHIRLPOOL ADG 2900 INSTALLATION

[. . . ] The installer is responsible for the installation. Improper installation is not covered under the Warranty. R R If the is to be relocated from one installation to another it must be kept upright to avoid damage from water spillage. R MODELS Prefinished Integrated BEFORE YOU START - DOUBLE & SINGLE MODELS PARTS SUPPLIED DOUBLE MODELS (INTEGRATED & PREFINISHED) INSTALLATION PREPARATION ELECTRICAL PREPARATION A) The switched power outlet for the appliance should be installed in a cabinet or on a wall adjacent to the under bench space in which the appliance is to be installed. Note: The power outlet must be accessible after installation. B) The power outlet should be positioned between 150mm and 450mm from the cavity. R (page 2 of 8) ELECTRICAL INFORMATION POWER SUPPLY CORD A) Care should be taken when the appliance is installed or removed, to reduce the likelihood of damage to the power supply cord. [. . . ] Water Softener Models Refer to your softener. Water Pressure Water Softener Models Other Models Maximum 1000kPa (145 p. s. i. ) 1000kPa (145 p. s. i. ) Minimum 100kPa (14. 5 p. s. i. ) 30kPa (4. 3 p. s. i. ) User Guide on how to set up your water + Option 2 with Waste Disposal. Standpipe Ø38mm with Air Gap. These marks indicate mounting tab screw locations (refer to step 1 page 5) Drain Connection Drain Hose Joiner to suit Ø19mm ± 2mm waste tee. Electrical Connection 230-240 VAC power outlet 4. 5Amps Minimum. Weight Full 42kg Prefinished Empty 28kg Prefinished Length of Services Drain hose - 2250mm Inlet hose - 1750mm Power supply cord - 1965mm NOTE: Services approximately exit product 189mm from left; 550mm from front; 393mm from top. NOTE: All depth measurements are taken from the front face of the adjacent cabinetry. NOTE: To align drawer front to adjacent cabinetry, the product to counter top clearance can be increased from 3mm. PLEASE NOTE: It is NOT recommended to connect the to any part of the Waste Disposal System. Option 3 using Sink Trap with Drain Hose Joiner. Ensure the edges of the services hole are smooth or covered. Cabinetry must not extend beyond cavity base NOTE: Prefinished Model is shown. There is no variation in plumbing between Prefinished products and Integrated products. Option 1 and 2 are the preferred options. Options 1 & 2 or use of a Dual Inlet Airgap satisfy Kosher requirements. 1Gb00079 28-11-2002 18:50 Pagina 3 INSTALLATION INSTRUCTIONS R READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY. (page 5 of 8) PLEASE NOTE: Your model of may differ from the model shown in the installation diagrams. Installation is similar for Integrated & Prefinished products for either Single or Double models. Information referring to Single models only is highlighted in blue. Installation diagrams have been simplified to enable clearer instruction. FOR INTEGRATED PRODUCTS FOLLOW THE INTEGRATED PANEL PREPARATION INSTRUCTIONS, BEFORE MOVING THE PRODUCT INTO THE CAVITY. 1 MOVING THE PRODUCT INTO THE CAVITY must be free to close completely. With overlapping integrated drawer fronts a 2. 5mm clearance must be maintained between drawer front and cabinetry. R 2 REMOVING THE TUB 3 ADJUSTING THE FEET DOUBLE MODELS ONLY 1 4 (SINGLE MODELS ONLY). Mark chassis position on cavity. MINIMUM CLEARANCE TO UNDERSIDE OF COUNTER 2. 5mm 6 5 2 DO NOT push middle of drawers. The product should NOT support any part of the kitchen cabinetry. 3 8 9 9 DOUBLE MODELS ONLY Adjust the height of the product to suit the cabinetry, by turning the feet from inside the product using a wrench or M5 socket. TIP - gently take the load off each foot using the slide and then turn by hand. NOTE: For integrated products, align the top of the upper panel with the top of the adjacent cabinetry. Be careful of sharp edges. MOUNTING TAB OPTIONS The mounting tabs are in pairs, one on each side of the product. They are used to secure the product to the cavity sides. Installation requires two sets of tab pairs be used, for example A and B tab pairs. A minimum installation requires that the B mounting tabs be used. 7 4 5 6 7 8 SINGLE MODELS ONLY. Gently open the drawer and mark the chassis position on the cavity, before removing the tub. [. . . ] Check water supply and drainage connection for leakage. LEAVE ALL LITERATURE WITH CUSTOMER. 24 DO NOT over tighten screws. Overtightening will damage the plastic mounting detail. 12 CUSTOMER SUPPORT 23 24 Partly open bottom drawer. Position Toe Kick behind door and slide onto the mounting rails on the underside of tub. [. . . ]