User manual WHIRLPOOL ADG 6446 NB PRODUCT FICHE

[. . . ] START BUTTON RESET FUNCTION: Press this button for at least 2 seconds; the selected programme and options will be cancelled. Main failure displays (repeated flashing of the START indicator lamp) can be cancelled by RESETTING. Detailed instructions are given in chapter "What to do if. . . ". START DELAY option MULTI ANTION/OFF ZONE BACTERIAL BUTTON RINSE option option (see at right for options description) Table of programmes Consumption Detergent P 1 2 3 4 5 1) 2) 3) Programmes Available options Loading instructions Litres kWh Minutes 1) RINSE AID INDICATOR When lit, the rinse aid dispenser needs to be refilled. AutoSensor 50-65°C Delay Recommended programme for Multizone routine washes, with dried-on food Antibacterial (e. g. rinse X 11-16 1. 10-1. 50 100-130 Pre-Wash cold Delay Multizone Crockery to be washed later. -- 4. 0 0. 03 14 Quickwash 45°C Delay Multizone Lightly soiled crockery, with no dried-on food. [. . . ] · Select a new programme · Press the START button. Switch off the appliance Everything o. k. . . . Exercise caution when opening the door: beware of hot steam. Only press the OFF button once the START indicator lamp has switched off. Unload the appliance, starting from the lower rack in order to avoid any residual drips of water falling onto crockery below. Maintenance and care Maintenance and care Screw on filter cylinder NOTE MARK!Unscrew filter cylinder, remove it and fine sieve. . . Insert Filters Check and clean if necessary Rectifying minor faults yourself . . . 10 Insert and screw on lower and upper arms tightly. Clean spray nozzles under running water (use toothpicks if necessary) . . . Spray arms Remove blockages/ deposits. GB -5- What to do if. . . If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation. . . . is not working/will not start . . . shows "F1" on the display or the START indicator lamp flashes once . . . shows "F4" on the display or the START indicator lamp flashes 4 times . . . shows "F6" on the display or the START indicator lamp flashes 6 times . . . shows "F7" on the display or the START indicator lamp flashes 7 times . . . shows "F8" on the display or the START indicator lamp flashes 8 times Possible causes. . . The water supply temperature is below 3°C. Kinked water inlet hose or clogged inlet filters. - If you use a combined action detergent, try adding more rinse aid. - Synthetic materials do not dry well; if wet at end of cycle, wipe dry. Clean dishes left in dishwasher for a long time after end - In this situation, the presence of drops of water on dishes and on the sides of the dishwasher is normal. when using "delayed start" option). releasing the door 5 minutes before removing the dishes. Incorrect arrangement of the concave items in the rack. - Arrange crockery so that water does not collect in cavities. - Increase the dosage of rinse aid - see page 3, "Adding rinse aid". - The rapid programme is intended for quickly washing lightly soiled dishes. If used for a full load of medium/ heavy soiled dishes, the dishes may not dry completely. If so, select a standard-length programme. For best results, open the door after the end of the programme and wait 15 minutes before unloading the dishwasher. [. . . ] - The open dishwasher door can only support the weight of the loaded rack when pulled out. Do not rest objects on the open door or sit or stand on it. - Sharp items that might cause injury (e. g. knives), must be placed in the cutlery basket with the sharp end facing downwards. [. . . ]