User manual WHIRLPOOL ADG 9928/1 INSTRUCTION FOR USE

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual WHIRLPOOL ADG 9928/1. We hope that this WHIRLPOOL ADG 9928/1 user guide will be useful to you.

Lastmanuals help download the user guide WHIRLPOOL ADG 9928/1.


Mode d'emploi WHIRLPOOL ADG 9928/1
Download

You may also download the following manuals related to this product:

   WHIRLPOOL ADG 9928/1 PROGRAM CHART (211 ko)

Manual abstract: user guide WHIRLPOOL ADG 9928/1INSTRUCTION FOR USE

Detailed instructions for use are in the User's Guide.

[. . . ] Before using the dishwasher, read the installation and maintenance instructions carefully! GB ADG 9928 1. OVERVIEW On button Programme selection button Press the button repeatedly until the desired programme indicator lights up. Start button Switches “on” when the dishwasher is operating. Switches off at the end of the programme. [. . . ] If the water hardness level falls within category 1 (soft), no salt is required. How to set the water hardness level - Switch on the appliance. - Select the 2nd programme “P2” - consult the table 1. 1 in chapter 1. - Press the START button for at least 5 seconds until the START indicator lamp flashes. - The set water hardness level is shown on the display (if present) or the START button flashes. - With each successive touch of the START button the setting increases and when it reaches 7 it returns to 1 again. - The appliance must be switched off to memorise the new setting. Water hardness 1 soft 1 - 2 medium 2 medium 3 medium-hard 4 hard 4 very hard 4 extremely hard German degrees °dH 0-5 6 - 10 11 - 15 16 - 21 22 - 28 29 - 35 36 - 60 French degrees °fH 0-9 10 - 18 19 - 27 28 - 37 38 - 50 51 - 63 64 - 107 English degrees °eH 0 - 6. 3 7 - 12. 6 13. 3 - 18. 9 19. 6 - 25. 9 26. 6 - 35 35. 7 - 44. 1 44. 8 - 74. 9 Flashing frequency or display setting 1 / 1x 2 / 2x 3 / 3x 4 / 4x 5 / 5x 6 / 6x 7 / 7x Water hardness level is factory set at 3 for medium-hard water (display 4 or 4 flashes of the START button). Only use dishwasher-proof crockery and dishes. Do not use the dishwasher for washing wooden items, aluminium, tin, silver cutlery or decorated crockery (unglazed). WASH CYCLE The dishwasher door must be closed and the water tap open. To load crockery, open the door with caution: beware of hot steam. The programme resumes the cycle from where it was interrupted. The wash cycle can be interrupted at any time by pressing RESET. Changing the programme in progress/Resetting - Press the START button for about 2 seconds, until the START indicator lamp switches off. - The appliance is now ready to be restarted. Full integrated models - Press the START/RESET button (for 2 seconds). - The appliance is now ready to be restarted. PROGRAMME END Exercise caution when opening the door: beware of hot steam. Only press the OFF button once the START indicator lamp has switched off. Unload the appliance, starting from the lower rack in order to avoid any residual drips of water falling onto crockery below. For even better drying results, leave the dishwasher door open a little before unloading in order to allow the steam to dissipate, helping the dishes to dry. The underside of the kitchen worktop must be protected (see instructions in “Maintenance and Installation”). 5 4. PRECAUTIONS AND GENERAL RECOMMENDATIONS 1. Packing The packaging materials are 100% recyclable and marked with the recycling symbol. Removing the packaging and inspecting the contents After unpacking, make sure that the dishwasher is undamaged and that the door closes correctly. [. . . ] WHAT TO DO IF. . . Crockery and cutlery . . . . . . are not perfectly clean/have food residues Possible causes/solutions . . . have deposits: - regeneration salt residue - rust marks In the event of frequent use of the Eco programme 50°C (if available), from time to time select the intensive 70°C programme (if available). The spray arms must not be clogged, the filters must not be dirty and must be fitted correctly (see the instructions in “Maintenance and installation”). The spray arms must be able to turn freely and must not be impeded by crockery or cutlery. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE WHIRLPOOL ADG 9928/1

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual WHIRLPOOL ADG 9928/1 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag