User manual WHIRLPOOL ADG 9994/1 PROGRAM CHART

[. . . ] Before using the dishwasher, read the installation and maintenance instructions carefully! GB ADG 9994 1. OVERVIEW On button Programme selection button Press the button repeatedly until the desired programme indicator lights up. Start button Switches “on” when the dishwasher is operating. Switches off at the end of the programme. [. . . ] - Press the START button for at least 5 seconds until the START indicator lamp flashes. - The set water hardness level is shown on the display (if present) or the START button flashes. - With each successive touch of the START button the setting increases and when it reaches 7 it returns to 1 again. - The appliance must be switched off to memorise the new setting. Water hardness 1 soft 1 - 2 medium 2 medium 3 medium-hard 4 hard 4 very hard 4 extremely hard German degrees °dH 0-5 6 - 10 11 - 15 16 - 21 22 - 28 29 - 35 36 - 60 French degrees °fH 0-9 10 - 18 19 - 27 28 - 37 38 - 50 51 - 63 64 - 107 English degrees °eH 0 - 6. 3 7 - 12. 6 13. 3 - 18. 9 19. 6 - 25. 9 26. 6 - 35 35. 7 - 44. 1 44. 8 - 74. 9 Flashing frequency or display setting 1 / 1x 2 / 2x 3 / 3x 4 / 4x 5 / 5x 6 / 6x 7 / 7x Water hardness level is factory set at 3 for medium-hard water (display 4 or 4 flashes of the START button). Water hardness level 4 with combined action detergent Even if you use a combined action detergent which includes salt, you must still add regeneration salt since such detergents are not effective enough at softening hard water. If the appliance is equipped with the function “Select detergent” (see chapter “1. Overview”), set the detergent dispenser system to the “no salt” setting so that the salt indicator lamp remains activated (“Detergent with rinse aid”). USING THE APPLIANCE LOADING THE RACKS TOP RACK - depending on model Multipurpose support A Three possible positions for long for utensils, cups and glasses. Dish holder B In horizontal position for cups/long utensils, in raised position for plates and stemware. - The appliance is now ready to be restarted. PROGRAMME END Take care when opening the door, as hot steam can escape. Press the OFF button only after the START button indicator has gone off. Unload the racks, starting from the bottom one in order to prevent any residual water dripping onto the dishes in the appliance. For better drying of dishes briefly open the appliance door before unloading, so that the steam can come out. The underside of the kitchen worktop must be protected (see “Maintenance and Installation” instructions). 5 4. PRECAUTIONS AND GENERAL RECOMMENDATIONS 1. Packing The packaging materials are 100% recyclable and marked with the recycling symbol. Removing the packaging and inspecting the contents After unpacking, make sure that the dishwasher is undamaged and that the door closes correctly. If in doubt, contact a qualified technician or your local retailer. Before using the dishwasher for the first time - The appliance is designed to operate at ambient temperatures of between 5°C and 45°C. - This dishwasher has been tested by the manufacturer to ensure it functions correctly. Such testing may leave slight drips/ water marks which will disappear with the first wash. Energy and water savings - Do not rinse crockery under running water. [. . . ] WHAT TO DO IF. . . Crockery and cutlery . . . . . . are not perfectly clean/have food residues Possible causes/solutions . . . have deposits: - regeneration salt residue - rust marks In the event of frequent use of the Eco programme 50°C (if available), from time to time select the intensive 70°C programme (if available). The spray arms must not be clogged, the filters must not be dirty and must be fitted correctly (see the instructions in “Maintenance and installation”). The spray arms must be able to turn freely and must not be impeded by crockery or cutlery. [. . . ]