User manual WHIRLPOOL ADL 952 WH INSTRUCTION FOR USE

[. . . ] • Make sure the inlet and drain hoses are kink-free and are not crushed. • If the hose length is not sufficient, please contact your local dealer or our After-Sales Service. • The inlet hose must be securely clamped to the water tap to prevent leaks. • The inlet water temperature varies according to the model installed. [. . . ] • Store the detergent, rinse aid and regeneration salt in a dry place out of the reach of children. General recommendations: • The open dishwasher door can only support the weight of the loaded rack when pulled out. Do not rest objects on the open door or sit or stand on it: the appliance may topple over!• Do not use solvents inside the dishwasher: risk of explosion!• Only use detergents, rinse aids and regeneration salts specially recommended for use in domestic dishwashers. • Before cleaning or carrying out maintenance, switch off the appliance, disconnect the mains plug and turn off the water tap. • If a fault occurs, switch off the appliance and turn off the water tap. • If necessary, the power cable may be replaced with one the same obtained from our After-Sales Service. The power cable must only be replaced by a qualified technician. • On completion of the programme switch off the dishwasher and turn off the water tap. For appliances with water stop system: The water inlet hose and plastic casing contain electrical components. Do not therefore cut the hose or immerse the plastic casing in water. If the hose is damaged switch off the appliance immediately. EC Declaration of conformity: This appliance has been designed, constructed and distributed in compliance with the safety requirements of EC Directives: 73/23/EC 89/336/EC 93/68/EC • • • Load capacity: 12 place settings. Black process 45. 0° 100. 0 LPI 5gb94301. fm Page 8 Wednesday, April 10, 2002 5:54 PM HOW TO FILL THE SALT CONTAINER From a water hardness category of 2 to 4, before using the dishwasher for the first time, fill the salt container with approximately 2 kg. regeneration salt and add 1lt water (to find out the hardness level of water in your area, contact your local Water Board or check the last bill you received). If the water hardness level does not correspond to position 3 on the selector (factory setting) or if the water hardness level changes: Turn the selector to the correct position: Set the water hardness by turning the selector fitted inside the dishwasher on the left hand internal wall by using a coin. Use the table below to set the dial to the correct setting: Hardness level 1 soft 2 average 3 medium 4 hard German degrees °dH 0-6 7 - 13 14 - 20 21 - 35 French degrees °fH 0 - 11 12 - 23 24 - 36 37 - 63 mmol/l Clarke scale or English degrees °eH 0 - 7. 5 8. 8 - 16. 3 17. 5 - 25. 0 26. 3 - 43. 8 Setting 0, 0 - 1, 1 1, 2 - 2, 3 2, 4 - 3, 6 3, 7 - 6, 3 1 2 3 4 If the water hardness level falls within category 1 (soft), no salt is required. How to fill the salt container Warning: Only use regeneration salts for use in domestic dishwashers!Do not fill the salt container with unsuitable substances, such as detergent, as this will cause irreparable damage to the water softener system. Unscrew the cap by turning it counter-clockwise. When first using the dishwasher: fill the salt container to the rim with water (approx. Fill the salt container to the rim with regeneration salt (using the filler provided) (when filling for the first time use min. Screw the cap back on by turning it clockwise. [. . . ] Only fill the detergent dispenser prior to starting a wash programme. How to fill the detergent dispenser: Programmes with pre-wash: - Pour 2/3 of the dosage recommended by the manufacturer into the large compartment (B). - Pour the remaining third in the small compartment (C). Programmes without pre-wash: - Pour the entire recommended dosage into the large compartment (B). [. . . ]